enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Hydraulic diameter - Wikipedia

   en.wikipedia.org/wiki/Hydraulic_diameter

   For a fully filled duct or pipe whose cross-section is a convex regular polygon, the hydraulic diameter is equivalent to the diameter of a circle inscribed within the wetted perimeter. This can be seen as follows: The N {\displaystyle N} -sided regular polygon is a union of N {\displaystyle N} triangles, each of height D / 2 {\displaystyle D/2 ...

3. Iron pipe size - Wikipedia

   en.wikipedia.org/wiki/Iron_pipe_size

   Iron Pipe Size (IPS or I.P.S.) pipe sizing system based on the inside diameter (ID) of pipe. It was widely used from the early 19th century to the mid 20th century and is still in use by some industries, including major PVC pipe manufacturers, as well as for some legacy drawings and equipment.

4. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

5. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   For example, NPS 2 inch and DN 50 are the same pipe, but the actual OD is 2.375 inches or 60.33 millimetres. The only way to obtain the actual OD is to look it up in a reference table. For pipe sizes of NPS 14 inch (DN 350) and greater the NPS size is the actual diameter in inches and the DN size is equal to NPS times 25 (not 25.4) rounded to a ...

6. Piping and plumbing fitting - Wikipedia

   en.wikipedia.org/wiki/Piping_and_plumbing_fitting

   This fitting (also known as a "bungalow fitting" or a "cottage fitting") is a sanitary tee that allows two trap arms to be connected at the same level. A toilet is the main connection, with the option of a right or left-hand outlet to the 3" inlet with a choice of 1-1/2" or 2" in size.

7. Electrical conduit - Wikipedia

   en.wikipedia.org/wiki/Electrical_conduit

   FMT is a raceway, but not a conduit and is described in a separate NEC Article 360. It only comes in 1/2" & 3/4" trade sizes, whereas FMC is sized 1/2" ~ 4" trade sizes. NEC 360.2 describes it as: "A raceway that is circular in cross section, flexible, metallic and liquidtight without a nonmetallic jacket."

8. Orangeburg pipe - Wikipedia

   en.wikipedia.org/wiki/Orangeburg_pipe

   [1] [2] It was used from the 1860s through the 1970s, when it was replaced by PVC pipe for water supply and ABS pipe for drain-waste-vent (DWV) applications. The name comes from Orangeburg, New York, the town in which most Orangeburg pipe was manufactured, largely by the Fiber Conduit Company. It changed its name to the Orangeburg Manufacturing ...

9. Duct (flow) - Wikipedia

   en.wikipedia.org/wiki/Duct_(flow)

   A duct with less than 0.75 mg/100m 2 is considered to be clean, per the NADCA standard. [7] A Hong Kong standard lists surface deposit limits of 1g/m 2 for supply and return ducts and 6g/m 2 for exhaust ducts, or a maximum deposit thickness of 60 μm in supply and return ducts, and 180 μm for exhaust ducts. [8]