enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Barrel threads - Wikipedia

   en.wikipedia.org/wiki/Barrel_threads

   Attaching the barrel to the receiver using a barrel nut and a barrel with a shoulder is an alternative to action threads, which has been used in firearms such as the Sten gun and AR-15. Hand tools Quick barrel change systems is an increasingly popular alternative, as seen in for example SIG Sauer 200 STR , Roessler Titan or Blaser R8 .

3. Barrel nut - Wikipedia

   en.wikipedia.org/wiki/Barrel_nut

   The barrel nut is a round slug, or formed sheet metal part with threads perpendicular to the length of the nut. The nut sits in a hole inside the forging and a standard bolt is threaded into the barrel nut from outside the sheet metal. They are preferred over a standard nut and bolt, because they do not require a flange to be machined or forged ...

4. Nut (hardware) - Wikipedia

   en.wikipedia.org/wiki/Nut_(hardware)

   Toggle Standard nut sizes subsection. ... Barrel nut, barrel bolt, binding barrel, Chicago screw, post and screw or connector bolt ... 3 ⁄ 16: 0.1875 4.763 5.18

5. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Width_across_flats

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

6. Ruger Precision Rifle - Wikipedia

   en.wikipedia.org/wiki/Ruger_Precision_Rifle

   The Ruger Precision Rifle has a proprietary Pre-Fit barrel system. Pre-chambered "Drop-In Ready" barrels can be purchased, and the correct headspace is set using a proprietary barrel nut design. The barrel is threaded to fit the Ruger action threads. This way, a competent gunsmith only needs an AR-15 barrel wrench and proper headspace gauges to ...

7. British Standard Whitworth - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Whitworth

   To simplify matters, the term hexagon is used in this section to denote either bolt head or nut. Two spanners, both nominal size 5 ⁄ 8 in, with a diagram superimposed to show the logic that allows them both to be nominal size 5 ⁄ 8 in when their actual sizes are clearly different (across-flats distance vs screw diameter). The across-flats ...

8. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   Standardization efforts in the late 19th and the early part of the 20th century reduced the range of sizes considerably. Now, it is less common to see machine screws larger than #14, or odd number sizes other than #1, #3 and #5. Even though #14 and #16 screws are still available, they are not as common as sizes #0 through #12. [citation needed]

9. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...