enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

3. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   The history of copper pipe is similar. In the 1930s, the pipe was designated by its internal diameter and a 1 ⁄ 16-inch (1.6 mm) wall thickness. Consequently, a 1-inch (25 mm) copper pipe had a 1 + 1 ⁄ 8-inch (28.58 mm) outside diameter. The outside diameter was the important dimension for mating with fittings.

4. Iron pipe size - Wikipedia

   en.wikipedia.org/wiki/Iron_pipe_size

   During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. [1] The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different ...

5. Piping and plumbing fitting - Wikipedia

   en.wikipedia.org/wiki/Piping_and_plumbing_fitting

   A reducer reduces the pipe size from a larger to a smaller bore (inner diameter). Alternatively, reducer may refer to any fitting which causes a change in pipe diameter. [15] This change may be intended to meet hydraulic flow requirements of the system or adapt to existing piping of a different size. The reduction length is usually equal to the ...

6. Copper tubing - Wikipedia

   en.wikipedia.org/wiki/Copper_tubing

   While pipe sizes in Australia are inch-based, they are classified by outside rather than inside diameter (e.g., a nominal 3 ⁄ 4 inch copper pipe in Australia has measured diameters of 0.750 inches outside and 0.638 inches inside, whereas a nominal 3 ⁄ 4 inch copper pipe in the U.S. and Canada has measured diameters of 0.875 inch outside and ...

7. List of welding codes - Wikipedia

   en.wikipedia.org/wiki/List_of_welding_codes

   Pipe welding (stainless steel) AWS D11.2: Welding (cast iron) AWS D14.1: Industrial mill crane welding AWS D14.3: Earthmoving & agricultural equipment welding AWS D14.4: Machinery joint welding AWS D14.5: Press welding AWS D14.6: Rotating Elements of Equipment AWS D14.9 Specification for the Welding of Hydraulic Cylinders AWS D15.1: Railroad ...

8. Oxy-fuel welding and cutting - Wikipedia

   en.wikipedia.org/wiki/Oxy-fuel_welding_and_cutting

   A welding feather is measured as 2X or 3X, with X being the length of the inner flame cone. The unburned carbon insulates the flame and drops the temperature to approximately 5,000 °F (2,760 °C). The reducing flame is typically used for hardfacing operations or backhand pipe welding techniques. The feather is caused by incomplete combustion ...

9. Submerged arc welding - Wikipedia

   en.wikipedia.org/wiki/Submerged_arc_welding

   Electrodes are available in straight lengths and coils. Their diameters may be 1.6, 2.0, 2.4, 3, 4.0, 4.8, and 6.4 mm. The approximate value of currents to weld with 1.6, 3.2 and 6.4 mm diameter electrodes are 150–350, 250–800 and 650–1350 amps respectively.