enow.com Web Search

  1. Ads

    related to: m6 button head dimensions width and length table

Search results

  1. Results from the WOW.Com Content Network
  2. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    Other (usually smaller) sizes may occur to reduce weight or cost, including the small series flange bolts defined in ISO 4162 which typically have hexagonal head sizes corresponding to the smaller 1st choice thread size (eg. M6 small series flange bolts have 8mm hexagonal heads, as would normally be found on M5 bolts). [10]

  3. Width across flats - Wikipedia

    en.wikipedia.org/wiki/Width_across_flats

    The table below shows dimensions of metric spanners for selected sizes of metric threads. [2] Note that with ISO 272 1982 the width across flats for M10, M12, M14 and M22 were changed from 17, 19, 22 and 32 mm respectively to the current standard.

  4. Preferred metric sizes - Wikipedia

    en.wikipedia.org/wiki/Preferred_metric_sizes

    A standard metric (concrete) block is 190 mm wide, 390 mm long, and 190 mm high, which allows for 10 mm mortar joints in between bricks, giving a standard unit size of 200 mm square by 400 mm long. [3] A standard metric brick is 90 by 57 by 190 mm; with 10 mm of mortar, that produces a standard unit of 100 mm x 200 mm. [3]

  5. Screw - Wikipedia

    en.wikipedia.org/wiki/Screw

    Head markings and properties for metric hex-head cap screws [41] Head marking Grade, material and condition Nominal size range (mm) Proof strength Yield strength, min. Tensile strength, min. Core hardness MPa ksi MPa ksi MPa ksi Class 3.6 [42] 1.6–36 180 26 190 28 330 48 B52–95 Class 4.6 Low or medium carbon steel 5–100 225 32.6 240 35

  6. Computer case screws - Wikipedia

    en.wikipedia.org/wiki/Computer_case_screws

    M6 x 10 x 8 means M6 male and female threading, 10 mm hex length, and 8 mm threaded length. Typically, M2.5 and M3 standoffs tighten with a 5 mm socket, M4 standoffs with a 6 mm socket, M5 standoffs with a 7 mm socket, and M6 standoffs with an 8 mm socket, but this is not always the case.

  7. List of thread standards - Wikipedia

    en.wikipedia.org/wiki/List_of_thread_standards

    Metric Screw Threads: M Profile: V Thread Form ASME B1.15-1995 (R2003) Unified Inch Screw Threads (UNJ Thread Form) V Thread Form ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe ...

  8. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

  9. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

  1. Ads

    related to: m6 button head dimensions width and length table