enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Plastic pipework - Wikipedia

   en.wikipedia.org/wiki/Plastic_pipework

   Pipes, fittings, valves, and accessories make up a plastic pressure pipe system. The range of pipe diameters for each pipe system does vary. However, the size ranges from 12 to 400 mm (0.472 to 15.748 in) and 3 ⁄ 8 to 16 in (9.53 to 406.40 mm). Pipes are extruded and are generally available in: 3 m (9.84 ft), 4 m (13.12 ft), 5 m (16.40 ft ...

3. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

4. Moody chart - Wikipedia

   en.wikipedia.org/wiki/Moody_chart

   where is the density of the fluid, is the average velocity in the pipe, is the friction factor from the Moody chart, is the length of the pipe and is the pipe diameter. The chart plots Darcy–Weisbach friction factor against Reynolds number Re for a variety of relative roughnesses, the ratio of the mean height of roughness of the pipe to the ...

5. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   The taper rate for all NPT threads is 1 inch of diameter in 16 inches of length (3 ⁄ 4 inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance of thread. The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′.

6. Corrugated plastic - Wikipedia

   en.wikipedia.org/wiki/Corrugated_plastic

   Corrugated plastic box used as reusable packaging Corrugated plastic dividers used to pack automotive components A Velomobile enclosed in corrugated plastic. Corrugated plastic or corriboard – also known under the trade names of Correx, Biplex, Cartonplast, Polyflute, Coroplast, FlutePlast, IntePro, Proplex, Twinplast, Corriflute and Corflute – refers to a wide range of extruded twin-wall ...

7. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   For pipe sizes of NPS 14 inch (DN 350) and greater the NPS size is the actual diameter in inches and the DN size is equal to NPS times 25 (not 25.4) rounded to a convenient multiple of 50. For example, NPS 14 has an OD of 14 inches or 355.60 millimetres, and is equivalent to DN 350.

8. Iron pipe size - Wikipedia

   en.wikipedia.org/wiki/Iron_pipe_size

   During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. [1] The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different ...

9. Corrugated stainless steel tubing - Wikipedia

   en.wikipedia.org/wiki/Corrugated_stainless_steel...

   Corrugated stainless steel tubing (CSST) is tubing made of stainless steel with corrugation on the inside or outside. CSST is not FAC (Flexible Appliance Connector) tubing. Presently, CSST and FAC tubing both use corrugated stainless steel tubing. In the past, FAC used corrugated brass tubing. However, FAC tubing is made only in lengths of 1 to ...