enow.com Web Search

  1. Ads

    related to: standard drawer sizes in mm diameter height

Search results

  1. Results from the WOW.Com Content Network
  2. 19-inch rack - Wikipedia

    en.wikipedia.org/wiki/19-inch_rack

    The size denotes the width of the faceplate for the installed equipment. The rack unit is a measure of vertical spacing and is common to both the 19 and 23-inch racks. Hole spacing is either on 1-inch (25 mm) centers (Western Electric standard), or the same as for 19-inch (482.6 mm) racks (0.625 in or 15.9 mm spacing).

  3. Rack unit - Wikipedia

    en.wikipedia.org/wiki/Rack_unit

    Rack with sample component sizes including an A/V half-rack unit. A rack unit (abbreviated U or RU) is a unit of measure defined as 1 + 3 ⁄ 4 inches (44.45 mm). [1] [2] It is most frequently used as a measurement of the overall height of 19-inch and 23-inch rack frames, as well as the height of equipment that mounts in these frames, whereby the height of the frame or equipment is expressed ...

  4. 32 mm cabinetmaking system - Wikipedia

    en.wikipedia.org/wiki/32_mm_cabinetmaking_system

    Distance of the holes in the row of holes: 32 mm; Diameter of the holes: 5 mm and 8 mm [clarification needed]. A typical 5 mm shelf stud may measure 15-16 mm long, and has a thin flange of about 7 mm diameter halfway at its length. Distance of the front row of holes to the front edge: 37 mm

  5. Filing cabinet - Wikipedia

    en.wikipedia.org/wiki/Filing_cabinet

    Lateral files are typically 20 inches (510 mm) deep and manufactured in 30,-36,-and-42-inch (760, 910, and 1,070 mm) widths and 2-, 3-, 4-, and 5-drawer versions. The 30-inch-wide (760 mm), two-drawer version is popular for use inside cubicle workstations, as it is engineered to fit under or alongside the cubicle work surfaces.

  6. List of disk drive form factors - Wikipedia

    en.wikipedia.org/wiki/List_of_disk_drive_form...

    4 in × 1 in × 5.75 in (101.6 mm × 25.4 mm × 146 mm) = 376.77344 cm³. This smaller form factor is similar to that used in an HDD by Rodime in 1983, which was the same size as the "half height" 3½" FDD, i.e., 1.63 inches high. Today, the 1-inch high ("slimline" or "low-profile") version of this form factor is the most popular form used in ...

  7. International Standard Payload Rack - Wikipedia

    en.wikipedia.org/wiki/International_Standard...

    The rack has internal mounting provisions to allow attachment of secondary structure. The ISPRs will be outfitted with a thin center post to accommodate sub-rack-sized payloads, such as the 483 mm (19-inch rack) Spacelab Standard Interface Rack (SIR) Drawer or the Space Shuttle Middeck Locker. Utility pass-through ports are located on each side ...

  8. AOL Mail

    mail.aol.com

    Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

  9. Drive bay - Wikipedia

    en.wikipedia.org/wiki/Drive_bay

    The difference between those widths and the name of the bay size is because it is named after the size of floppy that would fit in those drives, a 5.25-inch-wide square. Half-height drive bays are 1 + 5 ⁄ 8 inches (41.3 mm) high by 5 + 3 ⁄ 4 inches (146.1 mm) wide, and are the standard housing for CD and DVD drives in modern computers. They ...

  1. Ads

    related to: standard drawer sizes in mm diameter height