enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Threaded rod - Wikipedia

   en.wikipedia.org/wiki/Threaded_rod

   A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. [1] They are designed to be used in tension. [2] Threaded rod in bar stock form is often called all-thread (ATR); other names include fully-threaded rod, redi-rod, continuously-threaded rod ...

3. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

4. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

5. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   [4] The taper rate for all NPT threads is 1 inch of diameter in 16 inches of length (3 ⁄ 4 inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance of thread.

6. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe Thread Form ASME B1.21M-1997 (R2013) Metric Screw Threads - MJ Profile: V Thread Form BS 84: Tables of BS Whitworth, BS Fine and BS Pipe Threads: V Thread ...

7. Piping and plumbing fitting - Wikipedia

   en.wikipedia.org/wiki/Piping_and_plumbing_fitting

   Piping or tubing is usually inserted into fittings to make connections. Connectors are assigned a gender, abbreviated M or F. An example of this is a "3 ⁄ 4-inch female adapter NPT", which would have a corresponding male connection of the same size and thread standard (in this case also NPT).

8. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   Because only 5 ⁄ 8 of this height is cut, the difference between major and minor diameters is 5 ⁄ 4 × 0.8660 × P = 1.0825 × P, so the tap drill size can be approximated by subtracting the thread pitch from the major diameter.

9. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   For a taper thread, it is the diameter at the "gauge length" (plus/minus one thread pitch) from the small end of the thread. The taper is 1:16, meaning that for each 16 units of measurement increase in the distance from the end, the diameter increases by 1 unit of measurement.