enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. SAE J1772 - Wikipedia

   en.wikipedia.org/wiki/SAE_J1772

   SAE J1772, also known as a J plug or Type 1 connector after its international standard, IEC 62196 Type 1, is a North American standard for electrical connectors for electric vehicles maintained by SAE International under the formal title "SAE Surface Vehicle Recommended Practice J1772, SAE Electric Vehicle Conductive Charge Coupler".

3. IEC 62196 - Wikipedia

   en.wikipedia.org/wiki/IEC_62196

   From left: IEC Type 1/SAE J1772 inlet; Tesla NACS outlet; IEC Type 2 connector outlet IEC 62196 Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles is a series of international standards that define requirements and tests for plugs, socket-outlets, vehicle connectors and vehicle inlets for conductive charging of electric vehicles and is ...

4. Type 2 connector - Wikipedia

   en.wikipedia.org/wiki/Type_2_connector

   The IEC 62196-2 Type 2 connector (sometimes referred to as Mennekes for the German company that designed it) is used for charging electric vehicles using AC power, mainly within Europe, Australia, NZ and many other countries outside of North America. The Type 2 connector was adopted as the EU standard in 2013, with full compliance required by 2025.

5. Combined Charging System - Wikipedia

   en.wikipedia.org/wiki/Combined_Charging_System

   CCS1 (Combined Charging System Combo 1) plug as used in North America. It is an extension of the J1772 standard AC charging connector. CCS Combo 1 vehicle inlet showing the J1772 and the two DC fast-charging pins Connectors: Incomplete Combo 2 (left) showing the two large direct current (DC) pins below, while the four alternating current (AC) pins for neutral and three-phase are removed, while ...

6. SAE J3068 - Wikipedia

   en.wikipedia.org/wiki/SAE_J3068

   LIN-CP with Cable Node Case C - Connector Attached to EVSE LIN-CP / PWM-CP LIN-CP* *Case C with non-current-coded connector (SAE J3400/J1772) can signal up to 80A with PWM-CP † Power transfer using LIN-CP can exceed the current-coded limit of 63/70A: If Case B, then a LIN-CP Cable Node with a higher current rating must be present

7. Coaxial power connector - Wikipedia

   en.wikipedia.org/wiki/Coaxial_power_connector

   found in an ISP specific modem/router, plug with male type, 12VDC power connector, manufactured by ARRIS, unknown standard, photo above in male connector example 6.30 2.50 found in an ISP specific modem/router, 12VDC power connector, manufactured by Compal, unknown standard 6.30 3.00 Q Icom R75, R8500 6.50 ?.?? EIAJ RC-5322 6.50 3.00

8. Cable modem termination system - Wikipedia

   en.wikipedia.org/wiki/Cable_modem_termination_system

   A given headend may have between 1–12 CMTSs to service the cable modem population served by that headend or HFC hub. One way to think of a CMTS is to imagine a router with Ethernet interfaces (connections) on one side and coaxial cable RF interfaces on the other side. The Ethernet side is known as the Network Side Interface or NSI.

9. Ethernet crossover cable - Wikipedia

   en.wikipedia.org/wiki/Ethernet_crossover_cable

   A crossover cable may also be used to connect two hubs or two switches on their upstream ports. Because the only difference between the T568A and T568B pin and pair assignments are that pairs 2 and 3 are swapped, a crossover cable may be envisioned as a cable with one modular connector following T568A and the other T568B (see TIA/EIA-568 wiring ...