enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. List of scale model sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_scale_model_sizes

    1:14: 0.8571428 in: 21.77 mm Tamiya Tamiya 56301 RC 1:14 King Hauler, RC Tractor Trucks 1:14 Scale. 1:13.71: 22.225 mm Model railway scratchbuilders' scale at 7 ⁄ 8 inches to a foot, commonly used with 45 mm gauge track to represent 2 ft gauge prototypes. 1:13: 59 ⁄ 64 in: 23.44 mm Aurora "Monster Scenes" and "Prehistoric Scenes" Kits. 1:12 ...

  3. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  4. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    Thus, the outer diameter of a catheter in millimeters can be calculated by dividing the French size by 3. [2] For example, a catheter with a French size of 9 would have an outer diameter of approximately 3.07 mm. While the French scale aligns closely with the metric system, it introduces redundancy and the potential for rounding errors.

  5. Inch - Wikipedia

    en.wikipedia.org/wiki/Inch

    [13] [14] Technical details. The international standard symbol for inch is in ... 25.4 millimetres (1 inch is exactly 25.4 mm)

  6. National pipe thread - Wikipedia

    en.wikipedia.org/wiki/National_pipe_thread

    The taper rate for all NPT threads is 1 inch of diameter in 16 inches of length (3 ⁄ 4 inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance of thread. The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′.

  7. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  8. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

  9. Mesh (scale) - Wikipedia

    en.wikipedia.org/wiki/Mesh_(scale)

    Although such information contains long lists of sieve sizes, in practice sieves are normally used in series in which each member sieve is selected to pass particles approximately 1/ √ 2 smaller in diameter or 1/2 smaller in cross-sectional area than the previous sieve. For example the series 80mm, 63, 40, 31.5, 20, 16, 14, 10, 8, 6.3, 4, 2.8 ...