Search results
Results from the WOW.Com Content Network
Included here are both factory OE and examples of specific aftermarket specifications. Applying the correct tightening values for threaded engine fasteners is critical for any engine build. Listed here are both factory OEM values, some of which involve a torque-plus-angle tightening method, and OEM and aftermarket values which require only a ...
Kohler engine identifi cation numbers (model, specifi cation and serial) should be referenced for effi cient repair, ordering correct parts, and engine replacement. Model . . . . . . . . . . . . . . . . . . . . .
Torque Specs for Small Block Chevy Engines Part Bolt Size Minimum Maximum Camshaft Sprocket 5/16"-18 15 ft. lbs. 25 ft. lbs. Connecting Rod 3/8"-24 30 ft. lbs. 35 ft. lbs.
• Step 1: Torque the bolts to 110 lbf/ft (149 Nm) in the numerical sequence shown. • Step 2: Torque the bolts to 130 lbf/ft (176 Nm) in the numerical sequence shown. • Final step: Torque the bolts to 170 lbf/ft (231 Nm) in the numerical sequence shown.
torque settings for the following: bolts, nuts, plugs, fittings, and clamps. Exceptions to these torques are given in the Service Manual, if necessary. Be sure to use a torque wrench that has the proper range. Torque wrenches must be used properly in order to ensure that the correct torque is applied. Always use a smooth pull for torque ...
Cylinder Head to Engine Block Retaining Bolt (M8) - in sequence 30Y 22lbft Cylinder Head to Engine Block Retaining Bolt (M11) • First Pass in sequence 30Y 22lbft • Second Pass in sequence +90Degrees • Third Pass in sequence +70Degrees Engine Block Coolant Drain Hole Plug 60Y 44lbft Engine Block Coolant Heater (LS3) 50Y 37lbft
engine identification numbers Kohler engine identifi cation numbers (model, specifi cation and serial) should be referenced for effi cient repair, ordering correct parts, and engine replacement.
TORQUE SPECIFICATIONS3,5 CH18/CH20/ CH640 CH23 CH25/ CH730/CH740 Blower Housing and Sheet Metal M5 Fasteners 6.2 N·m (55 in. lb.) into new holes 4.0 N·m (35 in. lb.) into used holes M6 Fasteners 10.7 N·m (95 in. lb.) into new holes 7.3 N·m (65 in. lb.) into used holes Carburetor and Intake Manifold Intake Manifold Mounting Fastener (torque ...
Piston Cooling Orifices. 97 in. lbs. Main Cap Torque. 150 ft. lb. Crankshaft End-play. .0015” - .015”. Cylinder Head Torque: Lubricate all types of Cylinder Head Cap Screws for this application with clean SAE 30 engine oil. Grade 180 or 12.9 w/o washers (RELIANCE RP365 & RP366)
%PDF-1.6 %âãÏÓ 549 0 obj > endobj 571 0 obj >/Filter/FlateDecode/ID[0CDCF9FF690C224DB85E2A676BBCD985>]/Index[549 72]/Info 548 0 R/Length 117/Prev 8552136/Root 550 ...
Revised Cylinder Head Torque Specs for GM 3.1L and 3.4L Engines. Attention technicians: 1994-2002 GM 3.1L and 3.4L engines require a revised cylinder head bolt torque and tightening sequence. Be sure to follow this procedure for best results. Tighten the cylinder head bolts to 44 ft.lbs. (60 N-m) in the order shown in Figure 1.
Make Liter CID Engine Model Year Rod Torque Main Torque Cylinder Head Bolt Torque ACURA 1.6 97 D16A1 86-89 23 FT/LBS 40 FT/LBS 22, 47 FT/LBS ACURA 1.7 104 B17A1 92-93 14,23 FT/LBS 56 FT/LBS 22,61 FT/LBS ACURA 1.8 112 B18A1 90-94 30 FT/LBS 56 FT/LBS 22,61 FT/LBS
Torque Specifications for Ford 5.4L-330ci-V8.
crankshft main bearing caps / torque to yield first 100 lb.ft second 130 lb.ft final 90 degrees rotation crankcase breather assembly to crankcase 20 lb.ft crankcase ladder m12 x 25 and m8 x 30 90 lb.ft crankcase ladder, m10 x 25 46 lb.ft m12 tee assembly 18 lb.ft oil filler tube support bolt , m6 x 16 120 lb.in
Torque specifications are shown either as an exact figure, or a specific range . Follow any special instructions or multi-step directions carefully to assure correct final torque .
troubleshooting, service, and repair of the Toro engine. The Toro operator’s manual contains safety information and operating tips for safe operating practices. Avoid Unexpected Engine Start - Turn off engine and disconnect the spark plug before servicing engine.
Engine Identification Numbers. When ordering parts, or in any communication involving an engine, always give the Model, Specification, and Serial Numbers of the engine. The engine identification numbers appear a on decal (or decals) affixed to the engine shrouding. See Figure 1-1. An explanation of these numbers is shown in Figure 1-2. Figure 1-2.
Torque and Rebuild Specifications for John Deere 300 Series 3029, 4039, 4045, 6059 and 6068 Engines. Cylinder Liner Protrusion. .001” - .004”. Main Bearing Cap Screw Dubuque Engines.
1. Sequence for main bearing bolt tightening: Tighten main bearing bolts (1,2,3,4,5,6,7,8,9,10) with snug torque 5 kgfm. Turn only the main bearing bolts to 45° using the Angle Indexing tool in the same sequence (Part Number : 2576 5890 0204) or Standard tool available in market.
engine identification numbers Kohler engine identifi cation numbers (model, specifi cation and serial) should be referenced for effi cient repair, ordering correct parts, and engine replacement.