enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. 4043 aluminium alloy - Wikipedia

   en.wikipedia.org/wiki/4043_aluminium_alloy

   4043 aluminium alloy [1] [2] [3] is a wrought aluminium alloy with good corrosion resistance typically used as filler material [4] [5] for welding of aluminium parts. It contains high amounts of silicon (between 4.5 and 6%) and trace amounts of other metals. [6] It is grey in appearance and is sold as either welding wire or welding rod for TIG ...

3. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

4. Miller Electric - Wikipedia

   en.wikipedia.org/wiki/Miller_Electric

   Miller Electric is an American arc welding and cutting equipment manufacturing company based in Appleton, Wisconsin. Miller Electric, has grown from a one-man operation selling products in northeastern Wisconsin to what is today one of the world's largest manufacturers of arc welding and cutting equipment.

5. List of welding codes - Wikipedia

   en.wikipedia.org/wiki/List_of_welding_codes

   Welding - Studs and ceramic ferrules for arc stud welding: ISO 13919-1: Welding - Electron and laser-beam welded joints - Guidance on quality level for imperfections - Part 1: Steel ISO 13919-2: Welding - Electron and laser-beam welded joints - Guidance on quality level for imperfections - Part 2: Aluminium and its weldable alloys ISO 13920

6. Talk:Tap and die - Wikipedia

   en.wikipedia.org/wiki/Talk:Tap_and_die

   As for an equivalent chart for rods and dies instead of holes and taps, never seen one. Hope someone calculates one and posts it here someday. — ¾-10 02:47, 13 March 2008 (UTC) The shaft size for dies for class 3A threads is always the nominal diameter. 3/8 - 16 needs a 3/8 shaft, 10mm- 1.5 needs a 10mm shaft.

7. Threaded rod - Wikipedia

   en.wikipedia.org/wiki/Threaded_rod

   A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. [1] They are designed to be used in tension. [2] Threaded rod in bar stock form is often called all-thread (ATR); other names include fully-threaded rod, redi-rod, continuously-threaded rod ...

8. Welding Procedure Specification - Wikipedia

   en.wikipedia.org/wiki/Welding_Procedure...

   The Canadian Welding Bureau, through CSA Standards W47.1, [3] W47.2 [4] and W186, [5] specifies both a WPS and a Welding Procedure Data Sheet (WPDS) to provide direction to the welding supervisor, welders and welding operators. The WPS provides general information on the welding process and material grouping being welded, while the WPDS ...

9. Oxy-fuel welding and cutting - Wikipedia

   en.wikipedia.org/wiki/Oxy-fuel_welding_and_cutting

   The amount of heat applied to the metal is a function of the welding tip size, the speed of travel, and the welding position. The flame size is determined by the welding tip size. The proper tip size is determined by the metal thickness and the joint design. Welding gas pressures using oxy-acetylene are set in accordance with the manufacturer's ...