enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  3. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  4. Point (typography) - Wikipedia

    en.wikipedia.org/wiki/Point_(typography)

    He did not change the subdivisions (1 inch = 12 subdivisions = 72 points), but defined it strictly in terms of the royal foot, a legal length measure in France: the Didot point is exactly 1 ⁄ 864 of a French foot or 1 ⁄ 72 of a French inch, that is (by 1799) 15 625 ⁄ 41 559 mm or about 0.375 972 mm. Accordingly, one Didot point is exactly ...

  5. Caliber - Wikipedia

    en.wikipedia.org/wiki/Caliber

    medium-bore refers to calibers with a diameter of 0.33 inches (8.4 mm) to 0.39 inches (9.9 mm) large-bore refers to calibers with a diameter of 0.40 inches (10 mm) or larger There is much variance in the use of the term "small-bore", which over the years has changed considerably, with anything under 0.577 inches (14.7 mm) considered "small-bore ...

  6. Typographic unit - Wikipedia

    en.wikipedia.org/wiki/Typographic_unit

    The traditional typographic units are based either on non-metric units, or on odd multiples (such as 35 ⁄ 83) of a metric unit.There are no specifically metric units for this particular purpose, although there is a DIN standard sometimes used in German publishing, which measures type sizes in multiples of 0.25 mm, and proponents of the metrication of typography generally recommend the use of ...

  7. Body jewelry sizes - Wikipedia

    en.wikipedia.org/wiki/Body_jewelry_sizes

    A gauge number denotes a thickness on a standardized scale which, for most purposes, starts at 20g (0.812 mm thick— often used for the posts for nose studs), and increases in thickness (as the gauge number decreases) to 0g, then 00g, and rarely goes any further as these thicknesses come closer and closer to 1 ⁄ 2 ″.

  8. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    ANSI B94.11M-1979 sets size standards for jobber-length straight-shank twist drill bits from 1/64 inch through 1 inch in 1/64 inch increments. For Morse taper -shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to ...

  9. 3 - Wikipedia

    en.wikipedia.org/wiki/3

    It is the first unique prime, such that the period length value of 1 of the decimal expansion of its reciprocal, 0.333..., is unique. 3 is a twin prime with 5, and a cousin prime with 7, and the only known number such that ! − 1 and ! + 1 are prime, as well as the only prime number such that − 1 yields another prime number, 2.