enow.com Web Search

  1. Ad

    related to: m2 drill size calculator

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Below is a comprehensive drill and tap size chart for all drills and taps, ... but you must first calculate the pitch by converting the fraction of ... M2×0.4 2.2 mm ...

  3. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

  4. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    One aspect of this method of sizing is that the size increment between drill bits becomes larger as bit sizes get smaller: 100% for the step from 1/64 to 1/32, but a much smaller percentage between 1 47/64 and 1 3/4. Drill bit sizes are written as irreducible fractions. So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch.

  5. Tap and die - Wikipedia

    en.wikipedia.org/wiki/Tap_and_die

    where is the tap drill size, is the major diameter of the tap (e.g., 3 ⁄ 8 in for a 3 ⁄ 8-16 tap), and / is the thread pitch (1 ⁄ 16 inch in the case of a 3 ⁄ 8-16 tap). For a 3 ⁄ 8 -16 tap, the above formula would produce 5 ⁄ 16 , which is the correct tap drill diameter.

  6. Number drill sizes - Wikipedia

    en.wikipedia.org/?title=Number_drill_sizes&...

    This page was last edited on 19 December 2010, at 23:06 (UTC).; Text is available under the Creative Commons Attribution-ShareAlike 4.0 License; additional terms may apply.

  7. Talk:List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/Talk:List_of_drill_and_tap...

    White lines are standard metric drill sizes. Blue lines are standard metric drill sizes used for metric taps of the size indicated in the Tap Size column. The clearance sizes need to be left as drill nomenclature (3/64, 6.5 mm, #37) rather than converting to decimal dimensions since having that dimension you have to chase down the table to find ...

  8. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  9. Talk:Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Talk:Drill_bit_sizes

    Jobber-length drills are the most common type of drill. The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size. So a 1⁄2 in (12.7 mm) diameter drill will be able to drill a hole 4 1⁄2 in (114.3 mm) deep since it is nine times the diameter in length. A 1⁄8 in (3.2 mm) diameter ...

  1. Ad

    related to: m2 drill size calculator