enow.com Web Search

  1. Ads

    related to: hex bolt size chart metric and standard length guide book pdf

Search results

  1. Results from the WOW.Com Content Network
  2. Preferred metric sizes - Wikipedia

    en.wikipedia.org/wiki/Preferred_metric_sizes

    Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

  3. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

  4. List of thread standards - Wikipedia

    en.wikipedia.org/wiki/List_of_thread_standards

    ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993: ISO general-purpose metric screw threads—Basic dimensions: V Thread Form ISO 725:2009: ISO inch screw threads—Basic dimensions: V Thread ...

  5. ASTM A325 - Wikipedia

    en.wikipedia.org/wiki/ASTM_A325

    ASTM A325 is an ASTM International standard for heavy hex structural bolts, titled Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength. It defines mechanical properties for bolts that range from 1 ⁄ 2 to 1 + 1 ⁄ 2 inches (13 to 38 mm) in diameter.

  6. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  7. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    An ASME B18.2.1 compliant cap screw has somewhat tighter tolerances than a hex bolt for the head height and the shank length. The nature of the tolerance difference allows an ASME B18.2.1 hex cap screw to always fit where a hex bolt is installed but a hex bolt could be slightly too large to be used where a hex cap screw is designed in. Fine ...

  8. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    spanner (wrench) size and thread diameter of a hex nut. Width across flats is the distance between two parallel surfaces on the head of a screw or bolt, or a nut, mostly for torque transmission by positive locking. The term width across flats (AF) is used for the following forms: 2-socket = round material with two surfaces

  9. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    Imperial Metric fastening size conversion charts; International Thread Standards; Conversion chart Whitworth/BSF/AF and metric Archived 2 May 2010 at the Wayback Machine; Spanner Jaw Sizes Additional information and spanner jaw size table. Unified Screw Threads Series; ASME B1.1-2003 Unified Inch Screw Threads, (UN and UNR Thread Form)

  1. Ads

    related to: hex bolt size chart metric and standard length guide book pdf