Ads
related to: high-pinion dana 70 (new gm version) 3ebay.com has been visited by 1M+ users in the past month
- eBay Money Back Guarantee
Worry-Free Shopping.
eBay Is Here For You!
- Business & Industrial
From Construction to Catering.
eBay Has All B&I Products For You.
- Daily Deals
Lowest Prices on Top Items.
Save Money with eBay Deals.
- Gift Cards
eBay Gift Cards to the Rescue.
Give The Gift You Know They’ll Love
- eBay Money Back Guarantee
Search results
Results from the WOW.Com Content Network
The Dana 70 rear axle was first used in the Dodge W300 in 1958. The Dana 70 started out using 10 spline pinions and 23 spline axle shafts. The later, more current, Dana 70 axles use 29 spline pinions and 32 or 35 spline axle shafts. Dana offered two different limited slip differentials with the Dana 70, the "Powr-Lok" and the "Trac-Lok."
Dana 44 Front axles were known for utilizing locking hubs or a center axle disconnect system. However, a permanently locked-in Dana 44 is not uncommon. The Dana 44 has seen use in 1/4-, 1/2-, 3/4-, and 1-ton rated trucks. The Dana 44 was manufactured in kingpin and ball joint variations, as well as closed and open knuckle variations.
The GM AAM axle tubes exhibit a smaller diameter at the spindle compared to the AAM Dodge axles—measuring 4" for GM and 3.5" for Dodge from the housing. In design variation, newer GM trucks are aligned with Dodge axles. Additionally, GM incorporates a vibration damper on the yoke, while Dodge positions it on the drive shaft.
Dana 61 axle tag showing 3.73:1 ratio [1] The Dana 61 was made in semi-float and full-float axles for select 4×2 and 4x4 Ford 3 ⁄ 4-ton and 1 Ton Pickups and Vans from 1974 to 1987. A Dana 61 front axle was selectively used in Dodge 4×4 3 ⁄ 4-ton and 1 Ton pickups from 1987 to 1993. Although 3.07:1 and 3.31:1 gear sets are common for a ...
The Dana 50 has a "50" cast into the housing and is regarded to have more strength than a Dana 44, but not as much as a Dana 60. It was only produced in a reverse cut gear set aka a high pinion. The Dana 50 was made as a solid axle and as a Twin Traction Beam (TTB) which pivots in the center allowing the wheels to move independently of each ...
The first version was produced from 1985 to 1992. The second version, produced from 1993 to 1997 featured a stronger pinion/yoke. This corrected a known, but rare, issue of the pinion yoke nut working loose. The first and second versions of the 10.25 axle are colloquially known as “short pinion-yoke” and “long pinion-yoke” respectively.
The Dana S110 is a full floating, drop-out axle. Dana S110 axles are a step up in overall strength compared to the Dana 80. Ford started using this axle in 2005 model F-450 and F-550 trucks. Replacing the Dana 80 in some class 4 trucks, and the Dana S 135 in the rest of the trucks. Dodge started using the Dana S110 in their 2008 model 4500 and ...
Transfer case: New Process NP200 two-range, 1.91:1 low range; Axles: front: Dana 60; rear: Dana 70 full-floating; ratio: 5.87:1; Electrical system: 24 volt utilizing two 12 volt batteries in series; Brakes: Hydraulic, 4-wheeled drum; Fuel type: gas; Fuel capacity: 28 US gal (106 L; 23 imp gal) Top speed: 55 mph (89 km/h) Turning radius: 28 feet ...
Ads
related to: high-pinion dana 70 (new gm version) 3ebay.com has been visited by 1M+ users in the past month