Ads
related to: high-pinion dana 70 (new gm version) 1ebay.com has been visited by 1M+ users in the past month
- Home & Garden
From Generators to Rugs to Bedding.
You’ll Find Everything You Need
- Electronics
From Game Consoles to Smartphones.
Shop Cutting-Edge Electronics Today
- Daily Deals
Lowest Prices on Top Items.
Save Money with eBay Deals.
- Trending on eBay
Inspired by Trending Stories.
Find Out What's Hot and New on eBay
- Home & Garden
walmart.com has been visited by 1M+ users in the past month
Search results
Results from the WOW.Com Content Network
The Dana 70 rear axle was first used in the Dodge W300 in 1958. The Dana 70 started out using 10 spline pinions and 23 spline axle shafts. The later, more current, Dana 70 axles use 29 spline pinions and 32 or 35 spline axle shafts. Dana offered two different limited slip differentials with the Dana 70, the "Powr-Lok" and the "Trac-Lok."
The GM AAM axle tubes exhibit a smaller diameter at the spindle compared to the AAM Dodge axles—measuring 4" for GM and 3.5" for Dodge from the housing. In design variation, newer GM trucks are aligned with Dodge axles. Additionally, GM incorporates a vibration damper on the yoke, while Dodge positions it on the drive shaft.
Dana 61 axle tag showing 3.73:1 ratio [1] The Dana 61 was made in semi-float and full-float axles for select 4×2 and 4x4 Ford 3 ⁄ 4-ton and 1 Ton Pickups and Vans from 1974 to 1987. A Dana 61 front axle was selectively used in Dodge 4×4 3 ⁄ 4-ton and 1 Ton pickups from 1987 to 1993. Although 3.07:1 and 3.31:1 gear sets are common for a ...
Dana 44 Front axles were known for utilizing locking hubs or a center axle disconnect system. However, a permanently locked-in Dana 44 is not uncommon. The Dana 44 has seen use in 1/4-, 1/2-, 3/4-, and 1-ton rated trucks. The Dana 44 was manufactured in kingpin and ball joint variations, as well as closed and open knuckle variations.
The GM 9.25 IFS has been the main front differential in Four-wheel drive 3/4 Ton and 1 Ton GM trucks since 1988. The Dana 60 solid axle front end was used selectively in trucks with a higher GVWR from 1988 to 1991. The original Saginaw 9.5 differential, ring and pinion were modified to work with the independent front suspension.
The Dana 50 has a "50" cast into the housing and is regarded to have more strength than a Dana 44, but not as much as a Dana 60. It was only produced in a reverse cut gear set aka a high pinion. The Dana 50 was made as a solid axle and as a Twin Traction Beam (TTB) which pivots in the center allowing the wheels to move independently of each ...
The 880s used a 2-speed New Process Gear NP203 transfer case. A Dana 44 4.10:1 front axle and floating Dana 60 4:10.1 rear axle completed the setup. The trucks were equipped with front disc brakes and rear drum brakes. They had a military-rated top speed of 70 mph (110 km/h). [5]
The first version was produced from 1985 to 1992. The second version, produced from 1993 to 1997 featured a stronger pinion/yoke. This corrected a known, but rare, issue of the pinion yoke nut working loose. The first and second versions of the 10.25 axle are colloquially known as “short pinion-yoke” and “long pinion-yoke” respectively.
Ads
related to: high-pinion dana 70 (new gm version) 1ebay.com has been visited by 1M+ users in the past month
walmart.com has been visited by 1M+ users in the past month