enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. List of gear nomenclature - Wikipedia

    en.wikipedia.org/wiki/List_of_gear_nomenclature

    The Diametral Pitch (DP) is the number of teeth per inch of diameter of the pitch circle. The units of DP are inverse inches (1/in). [3] DP = Diametral Pitch PD = Pitch Circle Diameter in inches CP = Circular Pitch in inches n = Number of Teeth DP = n / PD The Diametral Pitch (DP) is equal to π divided by the Circular Pitch (CP). DP = 3.1416 / CP

  3. Sterling 10.5 axle - Wikipedia

    en.wikipedia.org/wiki/Sterling_10.5_axle

    At least till 2011 the 12 bolt semi float was still found with the heavy duty f-150. Gear ratios were 3.73 in 4x4 and either the 3.73 or 4.10 in the two-wheel-drive models. This was available in both limited slip and standard variations. All 4x4 came with limited slip (L on tag), it can also be determined from the axle code on the door jamb vin ...

  4. Gear inches - Wikipedia

    en.wikipedia.org/wiki/Gear_inches

    Gear inches is one way of measuring the gear ratio(s) of a bicycle, so that different gears and different bicycles can be compared in a consistent manner. Gear inches is an imperial measure corresponding to the diameter in inches of the drive wheel of a penny-farthing bicycle with equivalent ( direct-drive ) gearing.

  5. Super Turbine 300 - Wikipedia

    en.wikipedia.org/wiki/Super_Turbine_300

    In Drive at full throttle, it would upshift from low gear to high gear at 60–65 mph (97–105 km/h). Under light throttle, depending on the final drive ratio, it might upshift at 10-15 mph. From 1964-1967, Buick and Oldsmobile versions of this transmission used a torque converter with a variable-pitch stator called Switch-Pitch (by Buick) or ...

  6. Dana 60 - Wikipedia

    en.wikipedia.org/wiki/Dana_60

    Ring gear diameter: 9 3 ⁄ 4 " Axle shaft diameter 1.41” Front (32 spline) 1.46” Rear (32 spline) 1.50” Front (35 spline) 1.50” Rear (35 spline) Inner axle shaft splines: 16, 23, 30, 32, 33 or 35 Aftermarket inner axle shaft splines: 40 for after market, high performance axles, equivalent to Dana 70 components; Pinion shaft diameter: 1 ...

  7. List of Ford transmissions - Wikipedia

    en.wikipedia.org/wiki/List_of_Ford_transmissions

    1993–2008 4R70W—Strengthened AOD-E with lower 1st and 2nd gear ratios Application vary by year Ford F-Series; Ford Crown Victoria; Mercury Grand Marquis; Lincoln Town Car; Ford Mustang; Ford Expedition; Ford E-Series; 2003–2008 4R75E & 4R75W. Applications vary by year 4.2L, 4.6L, & 5.4L (2v & 3v) F150; Ford E-Series Van; Ford Expedition ...

  8. A Comprehensive Guide to RV Values and Trade-ins - AOL

    www.aol.com/comprehensive-guide-rv-values-trade...

    While there’s not a go-to RV depreciation calculator available online, some experts suggest that an RV loses about 20% of its value after the first year, a rate that slows significantly after that.

  9. Gear - Wikipedia

    en.wikipedia.org/wiki/Gear

    Worm-and-gear sets are a simple and compact way to achieve a high torque, low speed gear ratio. For example, helical gears are normally limited to gear ratios of less than 10:1 while worm-and-gear sets vary from 10:1 to 500:1. [45] A disadvantage is the potential for considerable sliding action, leading to low efficiency. [46]