enow.com Web Search

  1. Ads

    related to: inch to mm conversion chart

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  3. Ring size - Wikipedia

    en.wikipedia.org/wiki/Ring_size

    Originally in 1945, the divisions were based on the ring inside diameter in steps of 1 ⁄ 64 inch (0.40 mm). [6] However, in 1987 BSI updated the standard to the metric system so that one alphabetical size division equals 1.25 mm of circumferential length. For a baseline, ring size C has a circumference of 40 mm. [7]

  4. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    The Charrière is measured by the ''outer'' diameter, and is defined as 1 Fr = 1/3 mm, and thus 1 mm = 3 Fr; therefore the diameter of a round catheter in millimetres can be determined by dividing the French size by 3. [2] The French units roughly correspond to the outer circumference of the catheter (see table below).

  5. Conversion of units - Wikipedia

    en.wikipedia.org/wiki/Conversion_of_units

    Conversion of units is the conversion of the unit of measurement in which a quantity is expressed, typically through a multiplicative conversion factor that changes the unit without changing the quantity. This is also often loosely taken to include replacement of a quantity with a corresponding quantity that describes the same physical property.

  6. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  7. Template:Convert/list of units/length/short list - Wikipedia

    en.wikipedia.org/wiki/Template:Convert/list_of...

    ftin (feet and inches) ft m (foot m) inch: in in Use of ′ and ″ symbols violates MOSNUM so is not provided. 1.0 in (25 mm) in cm; in mm; Other: nautical mile: nmi nmi the international standard nautical mile For other nautical miles see the full list. 1.0 nmi (1.9 km; 1.2 mi) parsec: pc pc 1.0 pc (3.3 ly) light-year: ly ly 1.0 ly (63,000 AU ...

  8. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  9. Metric drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a chart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths).

  1. Ads

    related to: inch to mm conversion chart