enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The outermost 1 ⁄ 8 and the innermost 1 ⁄ 4 of the height H of the V-shape are cut off from the profile. The major diameter D maj is the diameter of the screw measured from the outer edge of the threads. The minor diameter D min (also known as the root diameter) is the diameter of the screw measured from the inner edge of the threads. The ...

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  4. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  5. British Standard Whitworth - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Whitworth

    To simplify matters, the term hexagon is used in this section to denote either bolt head or nut. Two spanners, both nominal size 5 ⁄ 8 in, with a diagram superimposed to show the logic that allows them both to be nominal size 5 ⁄ 8 in when their actual sizes are clearly different (across-flats distance vs screw diameter). The across-flats ...

  6. United States Standard thread - Wikipedia

    en.wikipedia.org/wiki/United_States_Standard_thread

    United States Standard thread (USS thread), also known as Sellers Standard thread, [1] Franklin Institute thread [1] and American Standard thread, [2] is a standard for inch based threaded fasteners and washers. [3] The USS standard is no longer supported. It, together with the SAE fastener standard, was incorporated into the Unified Thread ...

  7. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    Square head cap screws up to and including 3 ⁄ 4 inch (19.05 mm) have a head 1 ⁄ 8 inch (3.175 mm) larger than the shank; screws larger than 3 ⁄ 4 inch (19.05 mm) have a head 1 ⁄ 4 inch (6.35 mm) larger than the shank. [9] In 1919, Dyke defined them as screws that are threaded all the way to the head. [10] socket screw

  8. AOL Mail

    mail.aol.com

    Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

  9. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...