enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Useful conversions and formulas for air dispersion modeling

    en.wikipedia.org/wiki/Useful_conversions_and...

    Atmospheric pollutant concentrations expressed as mass per unit volume of atmospheric air (e.g., mg/m 3, μg/m 3, etc.) at sea level will decrease with increasing altitude because the atmospheric pressure decreases with increasing altitude.

  3. Air pollutant concentrations - Wikipedia

    en.wikipedia.org/wiki/Air_pollutant_concentrations

    Some express the concentrations as ppmv (parts per million by volume) and some express the concentrations as mg/m 3 (milligrams per cubic meter), while others require adjusting or correcting the concentrations to reference conditions of moisture content, oxygen content or carbon dioxide content.

  4. Threshold limit value - Wikipedia

    en.wikipedia.org/wiki/Threshold_limit_value

    Its units are in parts per million (ppm) for gases and in milligrams per cubic meter (mg/m 3) for particulates such as dust, smoke and mist. The basic formula for converting between ppm and mg/m 3 for gases is ppm = (mg/m^3) * 24.45 / molecular weight. This formula is not applicable to airborne particles.

  5. Parts-per notation - Wikipedia

    en.wikipedia.org/wiki/Parts-per_notation

    At 10 000 ppm the solution is a deep red colour. As the concentration decreases the colour becomes orange, then a vibrant yellow, with the final 1 ppm sample a very pale yellow. In science and engineering , the parts-per notation is a set of pseudo-units to describe small values of miscellaneous dimensionless quantities , e.g. mole fraction or ...

  6. Total dissolved solids - Wikipedia

    en.wikipedia.org/wiki/Total_dissolved_solids

    where TDS is expressed in mg/L and EC is the electrical conductivity in microsiemens per centimeter at 25 °C. The conversion factor k e varies between 0.55 and 0.8. [5] Some TDS meters use an electrical conductivity measurement to the ppm using the above formula. Regarding units, 1 ppm indicates 1 mg of dissolved solids per 1,000 g of water. [6]

  7. Molar concentration - Wikipedia

    en.wikipedia.org/wiki/Molar_concentration

    Molar concentration or molarity is most commonly expressed in units of moles of solute per litre of solution. [1] For use in broader applications, it is defined as amount of substance of solute per unit volume of solution, or per unit volume available to the species, represented by lowercase : [2]

  8. Orders of magnitude (molar concentration) - Wikipedia

    en.wikipedia.org/wiki/Orders_of_magnitude_(molar...

    inhaled osmium tetroxide is immediately dangerous to life or health (1 mg Os/m 3) [13] 10 −8: 10 −7: 101 nM: hydronium and hydroxide ions in pure water at 25 °C (pK W = 13.99) [14] 10 −6: μM: 10 −5: 10 −4: 180–480 μM: normal range for uric acid in blood [10] 570 μM: inhaled carbon monoxide induces unconsciousness in 2–3 ...

  9. Talk:Parts-per notation - Wikipedia

    en.wikipedia.org/wiki/Talk:Parts-per_notation

    The examples don't seem to be too accurate. A drop is usually defined as 0.05 ml, which then gives;. 1 drop in 50 ml = 1‰, 50ml is a very small cup 1 drop in 50 l = 1ppm 50 l is about 11 gallons, not 40 1 drop in 50 cubic metres = 1 ppb 1 drop = 1ppt, a 50 m swimming pool is 50*25*2 = 2,500 m^3 1 drop in 50,000,000 cubic metres = 1ppq, 50,000,000 m^3 is equivalent to a lake covering a square ...