enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Piping and plumbing fitting - Wikipedia

   en.wikipedia.org/wiki/Piping_and_plumbing_fitting

   Steel pipe is often joined with threaded connections; tapered threads are cut into the end of the pipe, and sealant is applied in the form of thread-sealing compound or thread seal tape (also known as PTFE or Teflon tape) and the pipe is screwed into a threaded fitting with a pipe wrench. Threaded steel pipe is widely used in buildings to ...

3. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′. The standard for Nominal Pipe Size (often abbreviated NPS, which should not be confused with the abbreviation NPS for the straight thread form standard) is loosely related to the inside diameter of Schedule 40 series of sizes.

4. Rivet - Wikipedia

   en.wikipedia.org/wiki/Rivet

   On many rivets, a size in 32nds may be stamped on the rivet head. Other makings on the rivet head, such as small raised or depressed dimples or small raised bars indicate the rivet's alloy. To become a proper fastener, a rivet should be placed in a hole ideally 4–6 thousandths of an inch larger in diameter.

5. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

6. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   British Standard Pipe (BSP) is a set of technical standards for screw threads that has been adopted internationally for interconnecting and sealing pipes and fittings by mating an external thread with an internal (female) thread.

7. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

8. Ball-peen hammer - Wikipedia

   en.wikipedia.org/wiki/Ball-peen_hammer

   A ball-peen or ball pein hammer, also known as a machinist's hammer, [1] is a type of peening hammer used in metalworking. It has two heads, one flat and the other, called the peen, rounded. It is distinguished from a cross-peen hammer, diagonal-peen hammer, point-peen hammer, or chisel-peen hammer by having a hemispherical peen.

9. List of DIN standards - Wikipedia

   en.wikipedia.org/wiki/List_of_DIN_standards

   DIN EN 10305-1: EN 10305-1: DIN 2448: Seamless Steel Pipes and Tubes – Dimensions, Conventional Masses per Unit Length: Canceled: DIN EN 10220: EN 10220: DIN 2527: Blank flanges – Nominal pressure 6 to 100: Withdrawn: DIN EN 1092-1: EN 1092-1: DIN 2860: Capillary Fittings; Bends 180° of Copper: Withdrawn: DIN 2982: Steel threaded pipe ...