enow.com Web Search

  1. Ads

    related to: m2 drill size conversion table

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Below is a comprehensive drill and tap size chart for all drills and taps, ... M2.2×0.45 2.25 mm Drill bit diameter Fractional size Drill wire gauge [2] [3]

  3. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    Drill bit sizes are written as irreducible fractions. So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a chart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths).

  4. Tap and die - Wikipedia

    en.wikipedia.org/wiki/Tap_and_die

    where is the tap drill size, is the major diameter of the tap (e.g., 10 mm for a M10×1.5 tap), and pitch is the pitch of the thread (1.5 mm in the case of a standard M10 tap) and so the correct drill size is 8.5 mm. This works for both fine and coarse pitches, and also produces an approximate 75% thread.

  5. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

  6. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    Unified Coarse/Fine diameters and tap drill sizes (U.S. units) Unified Coarse/Fine tap drill sizes (U.S. units) Imperial Metric fastening size conversion charts; International Thread Standards; Conversion chart Whitworth/BSF/AF and metric Archived 2 May 2010 at the Wayback Machine; Spanner Jaw Sizes Additional information and spanner jaw size ...

  7. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  8. Talk:List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/Talk:List_of_drill_and_tap...

    Blue lines are standard metric drill sizes used for metric taps of the size indicated in the Tap Size column. The clearance sizes need to be left as drill nomenclature (3/64, 6.5 mm, #37) rather than converting to decimal dimensions since having that dimension you have to chase down the table to find the actual drill that it represents.

  9. Bar stock - Wikipedia

    en.wikipedia.org/wiki/Bar_stock

    Drill rod diameters range from 0.0135 to 1.5 in (0.34 to 38.10 mm); in the United States diameters smaller than 27 ⁄ 64 th of an inch (11 mm) are made in letter drill sizes and number drill sizes, in addition to fractional sizes. Lengths are usually one or three feet (0.3048 or 0.9144 m).

  1. Ads

    related to: m2 drill size conversion table