enow.com Web Search

  1. Ads

    related to: steel beam span table

Search results

  1. Results from the WOW.Com Content Network
  2. Span (engineering) - Wikipedia

    en.wikipedia.org/wiki/Span_(engineering)

    In engineering, span is the distance between two adjacent structural supports (e.g., two piers) of a structural member (e.g., a beam). Span is measured in the horizontal direction either between the faces of the supports (clear span) or between the centers of the bearing surfaces (effective span): [1] A span can be closed by a solid beam or by ...

  3. I-beam - Wikipedia

    en.wikipedia.org/wiki/I-beam

    In Mexico, steel I-beams are called IR and commonly specified using the depth and weight of the beam in metric terms. For example, a "IR250x33" beam is approximately 250 mm (9.8 in) in depth (height of the I-beam from the outer face of one flange to the outer face of the other flange) and weighs approximately 33 kg/m (22 lb/ft).

  4. Pin and hanger assembly - Wikipedia

    en.wikipedia.org/wiki/Pin_and_hanger_assembly

    Attempts have been made to increase the safety of bridges with pin and hanger assemblies by adding some form of redundancy to the assembly. Retrofits that add redundancy to pin and hanger assemblies include adding a "catcher's mitt"‍—‌a short steel beam attached to the bottom of the cantilevered girder that extends out beneath the suspended girder to "catch" the suspended girder should ...

  5. Open web steel joist - Wikipedia

    en.wikipedia.org/wiki/Open_web_steel_joist

    K-Series Joists are standardized regarding depths, spans, and load-carrying capacities. There are 63 separate designations in the Load Tables, representing joist depths from 10 inches (250 mm) through 30 inches (760 mm) in 2 inches (51 mm) increments and spans through 60 feet (18,000 mm).

  6. Plate girder bridge - Wikipedia

    en.wikipedia.org/wiki/Plate_girder_bridge

    In a plate girder bridge, the plate girders are typically I-beams made up from separate structural steel plates (rather than rolled as a single cross-section), which are welded or, in older bridges, bolted or riveted together to form the vertical web and horizontal flanges of the beam. In some cases, the plate girders may be formed in a Z-shape ...

  7. Deflection (engineering) - Wikipedia

    en.wikipedia.org/wiki/Deflection_(engineering)

    The deflection at any point, , along the span of a center loaded simply supported beam can be calculated using: [1] = for The special case of elastic deflection at the midpoint C of a beam, loaded at its center, supported by two simple supports is then given by: [ 1 ] δ C = F L 3 48 E I {\displaystyle \delta _{C}={\frac {FL^{3}}{48EI}}} where

  8. List of longest continuous truss bridge spans - Wikipedia

    en.wikipedia.org/wiki/List_of_longest_continuous...

    The Braga Bridge is a continuous truss bridge. It was the fourth longest span of this type when it was completed in 1966. This list of continuous bridge spans ranks the world's continuous truss bridges in two listings: The first is ranked by the length of main span (the longest length of unsupported roadway) and the second by the total length of continuous truss spans.

  9. Structural steel - Wikipedia

    en.wikipedia.org/wiki/Structural_steel

    A steel Ɪ-beam, in this case used to support timber joists in a house Ɪ-beam (serif capital 'Ɪ'-shaped cross-section – in Britain these include Universal Beams (UB) and Universal Columns (UC); in Europe it includes the IPE, HE, HL, HD and other sections; in the US it includes Wide Flange (WF or W-Shape) and H sections)

  1. Ads

    related to: steel beam span table