enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

3. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

4. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   American Society of Mechanical Engineers National Pipe Thread Taper (NPT) [5] Nominal pipe size Thread density Thread pitch P Hand-tight engagement [6] Effective thread [6] Overall length L 4 [6] Actual outside diameter D Tap drill; Length L 1 Turns Diameter E 1 Length L 2 Turns Diameter E 2; inch inch −1 inch mm inch inch inch inch inch inch ...

5. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Metric Screw Threads: M Profile: V Thread Form ASME B1.15-1995 (R2003) Unified Inch Screw Threads (UNJ Thread Form) V Thread Form ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe ...

6. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

7. Screw thread - Wikipedia

   en.wikipedia.org/wiki/Screw_thread

   The nominal diameter of Metric (e.g. M8) and Unified (e.g. 5 ⁄ 16 in) threads is the theoretical major diameter of the male thread, which is truncated (diametrically) by 0.866 ⁄ 4 of the pitch from the dimension over the tips of the "fundamental" (sharp cornered) triangles.

8. British Association screw threads - Wikipedia

   en.wikipedia.org/wiki/British_Association_screw...

   The Thury thread form had the crests rounded at ⁠ 1 / 6 ⁠ p and the roots rounded at ⁠ 1 / 5 ⁠ p so the thread angle was close to 47.5° but not exactly. This was simplified in the BA thread definition by defining the thread angle to be 47.5° exactly and the thread form to be symmetrical with a depth of ⁠ 3 / 5 ⁠ p.

9. Wrench size - Wikipedia

   en.wikipedia.org/wiki/Wrench_size

   Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.