enow.com Web Search

  1. Ads

    related to: 1.5mm cortical screw sizes guide

Search results

  1. Results from the WOW.Com Content Network
  2. British Association screw threads - Wikipedia

    en.wikipedia.org/wiki/British_Association_screw...

    The major diameter is given by 6p 1.2, [4]: 12 rounded to two significant figures in mm and the hex head size (across the flats) is 1.75 times the major diameter. BA sizes are specified by the following British Standards: BS 57:1951 — B.A. screws, bolts and nuts; BS 93:1951 — Specification for British Association (B.A.) screw threads with ...

  3. Preferred metric sizes - Wikipedia

    en.wikipedia.org/wiki/Preferred_metric_sizes

    Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

  4. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

  5. List of DIN standards - Wikipedia

    en.wikipedia.org/wiki/List_of_DIN_standards

    ISO general purpose metric screw threads – Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm: Active: DIN 13-3: ISO general purpose metric screw threads – Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mm: Active: DIN 13-4

  6. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    The term fine adjustment screw typically refers to screws with threads from 40–100 TPI (Threads Per Inch) (0.5 mm to 0.2 mm pitch) and ultra fine adjustment screw has been used to refer to 100–254 TPI (0.2 mm to 0.1 mm pitch). These screws are most frequently used in applications where the screw is used to control fine motion of an object.

  7. List of screw drives - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_drives

    [1] In Japan, the male sizes are often designated as DTC-20, DTC-27, DTC-40 (discontinued) and DTC-45 corresponding to a respective screw head size of 3.2 mm, 4.6 mm, 6.4 mm and 7.7 mm; with the size of the screw measured across the widest portion of the mating part of the head. The most common sizes in use for consumer electronics are DTC-20 ...

  8. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The number series of machine screws has been extended downward to include #00-90 (0.047 in = 0.060 in − 0.013 in) and #000-120 (0.034 in = 0.060 in − 2 × 0.013 in) screws; [3] however, the main standard for screws smaller than #0 is ANSI/ASME standard B1.10 Unified Miniature Screw Threads. This defines a series of metric screws named after ...

  9. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  1. Ads

    related to: 1.5mm cortical screw sizes guide