enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    For Morse taper-shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to 3¼ inches, and a single 1/4 inch increment to 3½ inches. One aspect of this method of sizing is that the size increment between drill bits ...

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  4. Inch - Wikipedia

    en.wikipedia.org/wiki/Inch

    Subdivisions of an inch are typically written using dyadic fractions with odd number numerators; for example, two and three-eighths of an inch would be written as ⁠2 + 3 / 8 ⁠ ″ and not as 2.375″ nor as ⁠2 + 6 / 16 ⁠ ″. However, for engineering purposes fractions are commonly given to three or four places of decimals and have been ...

  5. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  6. Gauge (firearms) - Wikipedia

    en.wikipedia.org/wiki/Gauge_(firearms)

    The 14 gauge has not been loaded in the United States since the early 20th century, although the 2 + 916-inch (65 mm) hull is still made in France. [6] The very small 24 and 32 gauges are still produced and used in some European and South American countries. Punt guns, which use very large shells, are rarely encountered.

  7. ANSI/ASME Y14.1 - Wikipedia

    en.wikipedia.org/wiki/ANSI/ASME_Y14.1

    A size chart illustrating the ANSI sizes. In 1992, the American National Standards Institute adopted ANSI/ASME Y14.1 Decimal Inch Drawing Sheet Size and Format, [1] which defined a regular series of paper sizes based upon the de facto standard 8 + 1 ⁄ 2 in × 11 in "letter" size to which it assigned the designation "ANSI A".

  8. Help:Convert units - Wikipedia

    en.wikipedia.org/wiki/Help:Convert_units

    The hands value has at most one digit after the decimal mark, and has an optional fraction. ... + 3 ⁄ 4 hands (38.75 inches) {{convert|9.2+3/4 ... 15.1–16.3 hands ...

  9. Thousandth of an inch - Wikipedia

    en.wikipedia.org/wiki/Thousandth_of_an_inch

    A thousandth of an inch is a derived unit of length in a system of units using inches. Equal to 1 ⁄ 1000 of an inch, a thousandth is commonly called a thou / ˈ θ aʊ / (used for both singular and plural) or, particularly in North America, a mil (plural mils). The words are shortened forms of the English and Latin words for "thousand" (mille ...