enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Drywall - Wikipedia

    en.wikipedia.org/wiki/Drywall

    Various sized cuts of 1 ⁄ 2 in (13 mm) drywall with tools for maintenance and installation . Drywall (also called plasterboard, dry lining, [1] wallboard, sheet rock, gib board, gypsum board, buster board, turtles board, slap board, custard board, gypsum panel and gyprock) is a panel made of calcium sulfate dihydrate (), with or without additives, typically extruded between thick sheets of ...

  3. Cement board - Wikipedia

    en.wikipedia.org/wiki/Cement_board

    This 5 ⁄ 16 inch (7.9 mm) thick cement board is designed as an underlayment for tile floors. These are 3-by-5-foot (91 by 152 cm) sheets. These are 3-by-5-foot (91 by 152 cm) sheets. A cement board is a combination of cement and reinforcing fibers formed into sheets, of varying thickness that are typically used as a tile backing board. [ 1 ]

  4. Lath and plaster - Wikipedia

    en.wikipedia.org/wiki/Lath_and_plaster

    Metal lathing was spaced across a 13.5-inch (340 mm) center, attached by tie wires using lathers' nippers. Sometimes, the mesh was dimpled to be self- furring . In use as early as 1900, rock lath (also known as "button board," "plaster board" or "gypsum-board lath"), is a type of gypsum wall board (essentially an early form of drywall) with ...

  5. Plaster mold casting - Wikipedia

    en.wikipedia.org/wiki/Plaster_mold_casting

    The dried mold is then assembled, preheated, and the metal poured. Finally, after the metal has solidified, the plaster is broken from the cast part. The mold is usually damaged from the metal so reusing is usually not done. Discarded plaster can be recycled by grinding but care must be used since silica dust causes permanent lung damage. [1] [2]

  6. Ceramic mold casting - Wikipedia

    en.wikipedia.org/wiki/Ceramic_mold_casting

    Cross-sections as thin as 1.3 mm (0.051 in) are possible, with no upper limit. Typical tolerances are 0.1 mm for the first 25 mm (0.005 in for the first inch) and 0.003 mm per additional mm (0.003 in per each additional in). A draft of 1° is typically required. The typical surface finish is 2–4 um (75–150 uin) RMS. [2]

  7. Grimes Says She Didn't See One of Her Kids for 5 Months ... - AOL

    www.aol.com/lifestyle/grimes-says-she-didnt-see...

    The former couple is parents to sons X Æ A-Xii, 4, and Techno Mechanicus, 2, as well as daughter Exa Dark Sideræl, 3 Grimes Says She Didn't See One of Her Kids for 5 Months amid Year-Long ...

  8. Woman who stowed away on plane to Paris arrested ... - AOL

    www.aol.com/news/woman-stowed-away-plane-paris...

    A Russian woman who stowed away on a Delta Air Lines flight from New York to Paris last week is expected to face at least one federal charge after she returned to the United States Wednesday ...

  9. Who killed JonBenét Ramsey? Her dad believes DNA could reveal ...

    www.aol.com/killed-jonben-t-ramsey-her-070610776...

    A look back at how "48 Hours" covered the 1996 Christmastime murder of JonBenét Ramsey in 2002, and what her father John Ramsey says about the unsolved Colorado case nearly 28 years later.