enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. 6V6 - Wikipedia

    en.wikipedia.org/wiki/6V6

    6V6 Octal socket basing diagram. 1 - * Unconnected in all versions except for the shell connection of the metal 6V6 2 & 7 - Filament / Heater 3 - Anode / Plate 4 - Grid 2 / Screen Grid 5 - Grid 1 / Control Grid 6 - No connection. Pin normally absent 8 - Cathode & Beam-Forming Plates. The 6V6 is a beam-power tetrode vacuum tube.

  3. List of vacuum tubes - Wikipedia

    en.wikipedia.org/wiki/List_of_vacuum_tubes

    1.25 V or 1.4 V AC from a separate heater winding on CRT horizontal-output transformers, in half-indirectly heated EHT rectifiers; E – 6.3 V parallel heater; for 3-cell lead-acid vehicle crank batteries (mobile equipment) and for AC mains or horizontal-output transformers; F – 12.6 V DC parallel heater for 6-cell lead-acid vehicle crank ...

  4. EL34 - Wikipedia

    en.wikipedia.org/wiki/EL34

    The EL34 is a thermionic vacuum tube of the power pentode type. The EL34 was introduced in 1955 by Mullard, who were owned by Philips. [1] The EL34 has an octal base (indicated by the '3' in the part number) and is found mainly in the final output stages of audio amplification circuits; it was also designed to be suitable as a series regulator by virtue of its high permissible voltage between ...

  5. 6AQ5 - Wikipedia

    en.wikipedia.org/wiki/6AQ5

    The 6AQ5 [1] (Mullard–Philips tube designation EL90) is a miniature 7-pin (B7G) audio power output pentode vacuum tube with ratings virtually identical to the 6V6 at 250 V. [2] It was commonly used as an output audio amplifier in tube TVs and radios. It was also used in transmitter circuits. [3]

  6. EL84 - Wikipedia

    en.wikipedia.org/wiki/EL84

    In common with all 'E' prefix tubes, using the Mullard–Philips tube designation, it has a heater voltage of 6.3V. It can produce 17W output in Class AB1 in push–pull configuration. Many guitar-amplifiers routinely run EL84 tubes in excess of 400VDC, with the Traynor Guitarmate reportedly putting out 25W RMS with 2 EL84s in a push–pull ...

  7. 6P1P - Wikipedia

    en.wikipedia.org/wiki/6P1P

    The 6P1P (Russian: 6П1П) is a Soviet-made miniature 9-pin beam tetrode vacuum tube with ratings similar to the 6AQ5, EL90 and the 6V6. Because of a different pinout (a 9-pin base versus 7-pin base) than an 6AQ5/EL90, it cannot be used as a plug-in replacement for these types; however, it will work in the same circuit with component values ...

  8. Heating element - Wikipedia

    en.wikipedia.org/wiki/Heating_element

    Typically, thick-film heaters are printed on flat substrates, as well as on tubes in different heater patterns. These heaters can attain power densities of as high as 100 W/cm 2 depending on the heat transfer conditions. [13] The thick-film heater patterns are highly customizable based on the sheet resistance of the printed resistor paste.

  9. Shell-and-tube heat exchanger - Wikipedia

    en.wikipedia.org/wiki/Shell-and-tube_heat_exchanger

    The arrangement of tubes is a crucial design aspect. They are positioned in holes drilled in tube sheets, with the spacing between holes - known as tube pitch - being a key factor for both structural integrity and efficiency. [10] Tubes are typically organized in square or triangular patterns, and specific layouts are detailed in engineering ...