enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

3. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Metric Screw Threads: M Profile: V Thread Form ASME B1.15-1995 (R2003) Unified Inch Screw Threads (UNJ Thread Form) V Thread Form ASME B1.20.1-2013: Pipe Threads, General Purpose (Inch) Pipe Thread Form ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe ...

4. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

5. Nut (hardware) - Wikipedia

   en.wikipedia.org/wiki/Nut_(hardware)

   Mechanical specifications of Metric/English sized nuts [5] Material Proof strength Min. tensile yield strength Min. tensile ultimate strength Nut marking Nut class ISO 898 (Metric) Low or medium carbon steel 380 MPa (55 ksi) 420 MPa (61 ksi) 520 MPa (75 ksi) 5 Medium carbon steel Q&T: 580 MPa (84 ksi) 640 MPa (93 ksi) 800 MPa (116 ksi) 8 Alloy ...

6. Screw - Wikipedia

   en.wikipedia.org/wiki/Screw

   Thus, an M6 screw, which has a pitch of 1 mm, is made by threading a 6 mm shank, and the nut or threaded hole is made by tapping threads into a hole of 5 mm diameter (6 mm − 1 mm). Metric hexagon bolts, screws and nuts are specified, for example, in International Standards ISO 4014, ISO 4017, and ISO 4032. The following table lists the ...

7. List of DIN standards - Wikipedia

   en.wikipedia.org/wiki/List_of_DIN_standards

   ISO Metric Trapezoidal Screw Thread; Nominal Dimensions: Active: DIN 103-5: ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 8 to 100 mm Nominal Diameter: Active: DIN 103-6: ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 105 to 300 mm Nominal Diameter: Active: DIN 103-7

8. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   It is the main standard for bolts, nuts, and a wide variety of other threaded fasteners used in these countries. It has the same 60° profile as the ISO metric screw thread, but the characteristic dimensions of each UTS thread (outer diameter and pitch) were chosen as an inch fraction rather than a millimeter value.

9. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.