enow.com Web Search

  1. Ad

    related to: 25.4 mm inches conversion chart

Search results

  1. Results from the WOW.Com Content Network
  2. Inch - Wikipedia

    en.wikipedia.org/wiki/Inch

    The United States adopted the conversion factor 1 metre = 39.37 inches by an act in 1866. [30] In 1893, Mendenhall ordered the physical realization of the inch to be based on the international prototype metres numbers 21 and 27, which had been received from the CGPM, together with the previously adopted conversion factor. [31]

  3. Traditional point-size names - Wikipedia

    en.wikipedia.org/wiki/Traditional_point-size_names

    1 Comparison table. 2 See also. 3 Notes. 4 References. Toggle the table of contents. ... 25.4 mm: Six-line pica Inch: Double-trismégiste: Sabon Sechscicero [8 ...

  4. English units - Wikipedia

    en.wikipedia.org/wiki/English_units

    8.47 mm = 1 ⁄ 3 of an inch, the notional base unit under the Composition of Yards and Perches. Digit: 19.05 mm = 3 ⁄ 4 inch Finger: 22.23 mm = 7 ⁄ 8 inch Inch: 25.4 mm: 3 barleycorns (the historical legal definition) Nail (cloth) 57.15 mm: 3 digits = 2 + 1 ⁄ 4 inches = 1 ⁄ 16 yard Palm: 76.2 mm: 3 inches Hand: 101.6 mm: 4 inches ...

  5. Unit of length - Wikipedia

    en.wikipedia.org/wiki/Unit_of_length

    A ruler, depicting two customary units of length, the centimeter and the inch. A unit of length refers to any arbitrarily chosen and accepted reference standard for measurement of length. The most common units in modern use are the metric units, used in every country globally.

  6. United States customary units - Wikipedia

    en.wikipedia.org/wiki/United_States_customary_units

    Thickness of aluminum foil is measured in mils (1 ⁄ 1000 inch, or 0.0254 mm) in the United States. Cross-sectional area of electrical wire is measured in circular mils in the U.S. and Canada, one circular mil (cmil) being equal to 5.067 × 10 −4 mm 2 (or 7.854 × 10 −7 in 2 ).

  7. Inch of mercury - Wikipedia

    en.wikipedia.org/wiki/Inch_of_mercury

    Inch of mercury (inHg and ″Hg) is a non-SI unit of measurement for pressure. It is used for barometric pressure in weather reports , refrigeration and aviation in the United States . It is the pressure exerted by a column of mercury 1 inch (25.4 mm) in height at the standard acceleration of gravity .

  8. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

  9. Point (typography) - Wikipedia

    en.wikipedia.org/wiki/Point_(typography)

    A less precise definition is one pica equals 0.166 inches (4.2 mm), and one point 0.01383 inches (0.351 mm). [27] [33] It was also noticed that 83 picas is nearly equal to 35 cm, so the Type Founders Association also suggested using a 35 cm metal rod for measurements, but this was not accepted by every foundry. [27]

  1. Ad

    related to: 25.4 mm inches conversion chart