enow.com Web Search

  1. Ads

    related to: inch to decimal chart

Search results

  1. Results from the WOW.Com Content Network
  2. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a chart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths).

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  4. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    French catheter scale. The French scale, French gauge or Charrière system is commonly used to measure the size of a catheter. It is most often abbreviated as Fr, but can often be seen abbreviated as Fg, FR or F. It may also be abbreviated as CH or Ch (for Charrière, its inventor). However, simply gauge, G or GA generally refers to Birmingham ...

  5. Thousandth of an inch - Wikipedia

    en.wikipedia.org/wiki/Thousandth_of_an_inch

    A thousandth of an inch is a derived unit of length in a system of units using inches. Equal to 1000 of an inch, a thousandth is commonly called a thou / ˈθaʊ / (used for both singular and plural) or, particularly in North America, a mil (plural mils ). The words are shortened forms of the English and Latin words for "thousand" ( mille in ...

  6. Inch - Wikipedia

    en.wikipedia.org/wiki/Inch

    Subdivisions of an inch are typically written using dyadic fractions with odd number numerators; for example, two and three-eighths of an inch would be written as ⁠2 + 3 / 8 ⁠ ″ and not as 2.375″ nor as ⁠2 + 6 / 16 ⁠ ″. However, for engineering purposes fractions are commonly given to three or four places of decimals and have been ...

  7. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Wrench size. spanner (wrench) size and thread diameter of a hex nut. Width across flats is the distance between two parallel surfaces on the head of a screw or bolt, or a nut, mostly for torque transmission by positive locking. The term width across flats (AF) is used for the following forms: 2-socket = round material with two surfaces.

  8. American wire gauge - Wikipedia

    en.wikipedia.org/wiki/American_wire_gauge

    American Wire Gauge ( AWG) is a logarithmic stepped standardized wire gauge system used since 1857, predominantly in North America, for the diameters of round, solid, nonferrous, electrically conducting wire. Dimensions of the wires are given in ASTM standard B 258. [1] The cross-sectional area of each gauge is an important factor for ...

  9. ANSI/ASME Y14.1 - Wikipedia

    en.wikipedia.org/wiki/ANSI/ASME_Y14.1

    A size chart illustrating the ANSI sizes. In 1992, the American National Standards Institute adopted ANSI/ASME Y14.1 Decimal Inch Drawing Sheet Size and Format, [1] which defined a regular series of paper sizes based upon the de facto standard 8 + 1 ⁄ 2 in × 11 in "letter" size to which it assigned the designation "ANSI A".

  1. Ads

    related to: inch to decimal chart