Search results
Results from the WOW.Com Content Network
In unit systems where force is a derived unit, like in SI units, g c is equal to 1. In unit systems where force is a primary unit, like in imperial and US customary measurement systems , g c may or may not equal 1 depending on the units used, and value other than 1 may be required to obtain correct results. [ 2 ]
inch of water (39.2 °F) inH 2 O ≈ 999.972 kg/m 3 × 1 in × g 0: ≈ 249.082 Pa [33] kilogram-force per square millimetre: kgf/mm 2: ≡ 1 kgf/mm 2 = 9.806 65 × 10 6 Pa [33] kip per square inch: ksi ≡ 1 kipf/sq in ≈ 6.894 757 × 10 6 Pa [33] long ton per square foot: ≡ 1 long ton × g 0 / 1 sq ft ≈ 1.072 517 801 1595 × 10 5 Pa ...
1.0 mdyn (1.6 × 10 −5 gr f) Metric gravitational units: tonne-force: t-f t f: 1.0 t f (9.8 kN; 0.98 LT f; 1.1 ST f) tf tf kilogram-force: kg-f kg f: 1.0 kg f (9.8 N; 2.2 lb f) kgf kgf gram-force: g-f g f: 1.0 g f (9.8 mN; 0.035 oz f) gf gf milligram-force: mg-f mg f: 1.0 mg f (9.8 μN; 0.015 gr f) mgf mgf Avoirdupois-based units: poundal ...
For example, the freezing point of water is 0 °C and 32 °F, and a 5 °C change is the same as a 9 °F change. Thus, to convert from units of Fahrenheit to units of Celsius, one subtracts 32 °F (the offset from the point of reference), divides by 9 °F and multiplies by 5 °C (scales by the ratio of units), and adds 0 °C (the offset from the ...
10 −8: 10 −8 kg: Speculated approximate lower limit of the mass of a primordial black hole: 1.5 × 10 −8 kg: US RDA for vitamin D for adults [46] ~2 × 10 −8 kg Uncertainty in the mass of the International Prototype of the Kilogram (IPK) (±~20 μg) [47] 2.2 × 10 −8 kg Planck mass, [48] can be expressed as the mass of a 2 Planck ...
The dyne is defined as "the force required to accelerate a mass of one gram at a rate of one centimetre per second squared". [2] An equivalent definition of the dyne is "that force which, acting for one second, will produce a change of velocity of one centimetre per second in a mass of one gram".
Converts measurements to other units. Template parameters [Edit template data] This template prefers inline formatting of parameters. Parameter Description Type Status Value 1 The value to convert. Number required From unit 2 The unit for the provided value. Suggested values km2 m2 cm2 mm2 ha sqmi acre sqyd sqft sqin km m cm mm mi yd ft in kg g mg lb oz m/s km/h mph K C F m3 cm3 mm3 L mL cuft ...
In physics, natural unit systems are measurement systems for which selected physical constants have been set to 1 through nondimensionalization of physical units.For example, the speed of light c may be set to 1, and it may then be omitted, equating mass and energy directly E = m rather than using c as a conversion factor in the typical mass–energy equivalence equation E = mc 2.