enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Ford Mustang (second generation) - Wikipedia

   en.wikipedia.org/wiki/Ford_Mustang_(second...

   [7] Ford "decided to call it Mustang II, since it was a new type of pony car designed for an era of high gas prices and fuel shortages." [8] The Mustang II was 490 lb (222 kg) lighter and almost 19 in (483 mm) shorter than the 1973 Mustang, and derived from the subcompact Pinto platform. While sharing a limited number of driveline components ...

3. Mustang Aeronautics Mustang II - Wikipedia

   en.wikipedia.org/wiki/Mustang_Aeronautics_Mustang_II

   Robert Bushby acquired the rights to the Long Midget Mustang in 1959 and four years later began development of a two-seat, side-by-side version. This eventually flew in 1966 and plans were made available soon thereafter. [4] Rights to both the Midget Mustang and the Mustang II were sold to Mustang Aeronautics in 1992.

4. Mustang Aeronautics Midget Mustang - Wikipedia

   en.wikipedia.org/wiki/Mustang_Aeronautics_Midget...

   Midget Mustang. The Mustang Aeronautics Midget Mustang MM-1 is a single-seat aerobatic sports airplane developed and marketed in the United States for homebuilding. [1] [2] It is also known as the Long Midget. It was the predecessor to the Mustang II which is also known as the Bushby Mustang. Rights to both the Midget Mustang and the Mustang II ...

5. Ford Mustang II (concept car) - Wikipedia

   en.wikipedia.org/wiki/Ford_Mustang_II_(concept_car)

   The Ford Mustang II is a small, front-engined (V8), open "two-plus-two" concept car built by the Ford Motor Company in 1963. Although bearing the same name as the first generation production Mustang, the four-seater Mustang II which closely resembled the final production variant that would appear in 1964, was intended primarily for the auto show circuit.

6. Crossmember - Wikipedia

   en.wikipedia.org/wiki/Crossmember

   A crossmember, also known as a K-frame, is a structural component that is transverse to the main structure of a vehicle. [1] In the automotive industry , this term typically refers to a steel component, often boxed, that is bolted across the underside of a monocoque (unibody) motor vehicle to support the engine and the transmission .

7. Ford Mustang (fifth generation) - Wikipedia

   en.wikipedia.org/wiki/Ford_Mustang_(fifth...

   The size of the 2010 Mustang GT's dual exhaust tips had been increased by one-half of an inch to 3.5 in (89 mm) while the exhaust note has been improved to enhance the sound of the V8. [54] Like the base V6-equipped Mustang, the 2010 Mustang GT included new spring rates and dampers to improve ride quality and control.

8. Ford Mustang (fourth generation) - Wikipedia

   en.wikipedia.org/wiki/Ford_Mustang_(fourth...

   The Mustang's front suspension makes use of MacPherson struts with longer lower control arms, new spindles, anti-roll bars, and other enhancements over 1993 and older Mustangs. At the rear, a four-bar link solid axle was used. [9] The 1994 Mustang's standard rear axle ratio was 2.73:1, though this was later changed to 3.27:1.

9. Ford Mustang (seventh generation) - Wikipedia

   en.wikipedia.org/wiki/Ford_Mustang_(seventh...

   The seventh-generation Ford Mustang is a pony car manufactured by Ford.First shown at the 2022 North American International Auto Show, it is assembled at Ford's Flat Rock Assembly Plant and began production on May 1, 2023, [4] [5] initially available with either the redesigned 2.3 L EcoBoost turbocharged 4-cylinder with 315 horsepower, or the revised, 4th generation Coyote V8 with 480–486 ...