enow.com Web Search

  1. Ads

    related to: rj45 connector through hole covers for wire gauge chart

Search results

  1. Results from the WOW.Com Content Network
  2. Registered jack - Wikipedia

    en.wikipedia.org/wiki/Registered_jack

    A cable with a 50-pin connector on one end can support six fully wired 8P8C connectors or Ethernet ports on a patch panel with one spare pair. Alternatively, only the necessary pairs for 10/100 Ethernet can be wired allowing twelve Ethernet ports with a single spare pair. This connector is also used with spring bail locks for SCSI-1 connections.

  3. Category 5 cable - Wikipedia

    en.wikipedia.org/wiki/Category_5_cable

    Category 5 cable is nearly always terminated with 8P8C modular connectors (often referred to incorrectly as RJ45 connectors [14] [15] [16]). The cable is terminated in either the T568A scheme or the T568B scheme. The two schemes work equally well and may be mixed in an installation so long as the same scheme is used on both ends of each cable.

  4. American wire gauge - Wikipedia

    en.wikipedia.org/wiki/American_wire_gauge

    The AWG originated in the number of drawing operations used to produce a given gauge of wire. Very fine wire (for example, 30 gauge) required more passes through the drawing dies than 0 gauge wire did. Manufacturers of wire formerly had proprietary wire gauge systems; the development of standardized wire gauges rationalized selection of wire ...

  5. ANSI/TIA-568 - Wikipedia

    en.wikipedia.org/wiki/ANSI/TIA-568

    Perhaps the most comprehensive known and most discussed feature of ANSI/TIA-568 is the definition of the pin-to-pair assignments, or pinout, between the pins in a connector (a plug or a socket) and the wires in a cable. Pinouts are critical because cables do not function if the pinouts at their two ends aren't correctly matched.

  6. Telephone jack and plug - Wikipedia

    en.wikipedia.org/wiki/Telephone_jack_and_plug

    For example, telephone cables in the UK typically have a BS 6312 (UK standard) plug at the wall end and a 6P4C or 6P2C modular connector at the telephone end: this latter may be wired as per the RJ11 standard (with pins 3 and 4), or it may be wired with pins 2 and 5, as a straight-through cable from the BT plug (which uses pins 2 and 5 for the ...

  7. File:Comparison wire gauge sizes.svg - Wikipedia

    en.wikipedia.org/wiki/File:Comparison_wire_gauge...

    comparison wire gauge sizes: Image title: Comparison of SWG (red), AWG (blue) and IEC 60228 (black) wire gauge sizes from 0.03 to 200 mm² to scale on a 1 mm grid, by CMG Lee. In the SVG file, hover over an item to highlight it. Width: 100%: Height: 100%

  8. Wire gauge - Wikipedia

    en.wikipedia.org/wiki/Wire_gauge

    Each notch is stamped with a number, and the wire or sheet, which just fits a given notch, is stated to be of, say, No. 10, 11, 12, etc., of the wire gauge. The circular forms of wire gauge measurement devices are the most popular, and are generally 3 + 3 ⁄ 4 inches (95 mm) in diameter, with thirty-six notches; many have the decimal ...

  9. IDC (electrical connector) - Wikipedia

    en.wikipedia.org/wiki/IDC_(electrical_connector)

    In some instances USB through version 2 on motherboards – 2.54 mm pitch, 10 pins, 2×5 (2 rows of 5 pins) [9] For all of the above connectors, the computer manufacturer typically attaches a female IDC connector onto one end of a ribbon cable, and later slides that connector onto a matching male box header or pin header on the computer ...

  1. Ads

    related to: rj45 connector through hole covers for wire gauge chart