enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. RDRAM - Wikipedia

    en.wikipedia.org/wiki/RDRAM

    To emphasize the advantages of the DDR technique, this type of RAM was marketed at speeds twice the actual clock rate, i.e. the 400 MHz Rambus standard was named PC-800. This was significantly faster than the previous standard, PC-133 SDRAM , which operated at 133 MHz and delivered 1066 MB/s of bandwidth over a 64-bit bus using a 168-pin DIMM ...

  3. DDR SDRAM - Wikipedia

    en.wikipedia.org/wiki/DDR_SDRAM

    A single read or write operation for the DDR4 SDRAM consists of a single 8n-bit-wide 4-clock data transfer at the internal DRAM core and 8 corresponding n-bit-wide half-clock-cycle data transfers at the I/O pins. [20] RDRAM was a particularly expensive alternative to DDR SDRAM, and most manufacturers dropped its support from their chipsets ...

  4. Synchronous dynamic random-access memory - Wikipedia

    en.wikipedia.org/wiki/Synchronous_dynamic_random...

    Normal operations resume on the rising edge of the clock after the one where CKE is sampled high. Put another way, all other chip operations are timed relative to the rising edge of a masked clock. The masked clock is the logical AND of the input clock and the state of the CKE signal during the previous rising edge of the input clock. CS chip ...

  5. DDR4 SDRAM - Wikipedia

    en.wikipedia.org/wiki/DDR4_SDRAM

    DDR4 speeds are advertised as double the base clock rate due to its Double Data Rate (DDR) nature, with common speeds including DDR4-2400 and DDR4-3200, and higher speeds like DDR4-4266 and DDR4-5000 available at a premium. Unlike DDR3, DDR4 does not have a low voltage variant; it consistently operates at 1.2 V. Additionally, DDR4 improves on ...

  6. Dynamic random-access memory - Wikipedia

    en.wikipedia.org/wiki/Dynamic_random-access_memory

    These numbers represent t CL-t RCD-t RP-t RAS in multiples of the DRAM clock cycle time. Note that this is half of the data transfer rate when double data rate signaling is used. JEDEC standard PC3200 timing is 3-4-4-8 [38] with a 200 MHz clock, while premium-priced high performance PC3200 DDR DRAM DIMM might be operated at 2-2-2-5 timing. [39]

  7. Memory timings - Wikipedia

    en.wikipedia.org/wiki/Memory_timings

    Without knowing the clock frequency it is impossible to state if one set of timings is "faster" than another. For example, DDR3-2000 memory has a 1000 MHz clock frequency, which yields a 1 ns clock cycle. With this 1 ns clock, a CAS latency of 7 gives an absolute CAS latency of 7 ns. Faster DDR3-2666 memory (with a 1333 MHz clock, or 0.75 ns ...

  8. DDR3 SDRAM - Wikipedia

    en.wikipedia.org/wiki/DDR3_SDRAM

    With two transfers per cycle of a quadrupled clock signal, a 64-bit wide DDR3 module may achieve a transfer rate of up to 64 times the memory clock speed. With data being transferred 64 bits at a time per memory module, DDR3 SDRAM gives a transfer rate of (memory clock rate) × 4 (for bus clock multiplier) × 2 (for data rate) × 64 (number of ...

  9. DDR5 SDRAM - Wikipedia

    en.wikipedia.org/wiki/DDR5_SDRAM

    Standard DDR5 memory speeds range from 4,000 to 6,400 million transfers per second (PC5-32000 to PC5-51200). [3] Higher speeds may be added later, as happened with previous generations. Compared to DDR4 SDRAM, the minimum burst length was doubled to 16, with the option of "burst chop" after eight transfers.