enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  3. Hardboard - Wikipedia

    en.wikipedia.org/wiki/Hardboard

    Tempered hardboard is a hardboard that has been coated with a thin film of linseed oil and then baked; this gives it more water resistance, impact resistance, hardness, rigidity and tensile strength. An earlier tempering process involved immersing the board in linseed oil or tung oil until it was 5 to 6 percent saturated, and heating to 170 °C ...

  4. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

  5. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

  6. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The major diameter may be slightly different from the shank diameter, which is the diameter of the unthreaded part of the screw. The diameters are sometimes given approximately in fractions of an inch (e.g. the major diameter of a #6 screw is 0.1380 in, approximately 9 ⁄ 64 in = 0.140625 in. The pitch P is the distance between thread peaks.

  7. Fiberboard - Wikipedia

    en.wikipedia.org/wiki/Fiberboard

    Medium-density fiberboard (MDF) and hardboard Fiberboard ( American English ) or fibreboard ( British English ) is a type of engineered wood product that is made out of wood fibers . Types of fiberboard (in order of increasing density) include particle board or low-density fiberboard (LDF), medium-density fiberboard (MDF), and hardboard or high ...

  8. The Strange Way Giraffes Fight - AOL

    www.aol.com/strange-way-giraffes-fight-140232689...

    Male giraffes use their powerful necks to fight each other over the right to mate with females or for territorial rights. ©TK166/Shutterstock.com

  9. Screwfix - Wikipedia

    en.wikipedia.org/wiki/Screwfix

    Screwfix Direct Limited, trading as Screwfix, is a retailer of trade tools, accessories and hardware products based in the United Kingdom. [6] Founded in 1979 as the Woodscrew Supply Company, the company was acquired in July 1999 by Kingfisher plc , which also owns B&Q , and is listed on the London Stock Exchange .