enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

3. Metric drill bit sizes - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_sizes

   N · 0.1 + 0.08 mm; From 1.0 through 2.95 mm, sizes are defined as follows, where N is an integer from 10 through 29: N · 0.1 mm; N · 0.1 + 0.05 mm; From 3.0 through 13.9 mm, sizes are defined as follows, where N is an integer from 30 through 139: N · 0.1 mm; From 14.0 through 25.0 mm, sizes are defined as follows, where M is an integer from ...

4. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Width_across_flats

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

5. Template:Convert/list of units - Wikipedia

   en.wikipedia.org/wiki/Template:Convert/list_of_units

   1.0 cm 2 (0.16 sq in) cm2 sqin; square millimetre: mm2 mm 2: US spelling: square millimeter: 1.0 mm 2 (0.0016 sq in) mm2 sqin; non-SI metric: hectare: ha ha 1.0 ha (2.5 acres) Imperial & US customary: square mile: sqmi sq mi 1.0 sq mi (2.6 km 2) sqmi km2; acre: acre (none) 1.0 acre (0.40 ha) square yard: sqyd sq yd 1.0 sq yd (0.84 m 2) square ...

6. British Standard Whitworth - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Whitworth

   The Leica Thread-Mount used on rangefinder cameras and on many enlarging lenses is 1 + 17 ⁄ 32 in by 26 turns-per-inch Whitworth, an artifact of this having been developed by a German company specializing in microscopes and thus equipped with tooling capable of handling threads in inches and in Whitworth.

7. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

8. NYT ‘Connections’ Hints and Answers Today, Friday, December 13

   www.aol.com/nyt-connections-hints-answers-today...

   1. These are commonly found in myths, legends and stories. 2. These are used to sort/organize digital messages. 3. Fizzy beverages with a sharp, zesty taste. 4. The words in this category sound ...

9. Tap and die - Wikipedia

   en.wikipedia.org/wiki/Tap_and_die

   where is the tap drill size, is the major diameter of the tap (e.g., 3 ⁄ 8 in for a 3 ⁄ 8-16 tap), and / is the thread pitch (1 ⁄ 16 inch in the case of a 3 ⁄ 8-16 tap). For a 3 ⁄ 8 -16 tap, the above formula would produce 5 ⁄ 16 , which is the correct tap drill diameter.