enow.com Web Search

  1. Ads

    related to: 30lb felt vs 15 lb oak plywood sheets dimensions weight

Search results

  1. Results from the WOW.Com Content Network
  2. Bituminous waterproofing - Wikipedia

    en.wikipedia.org/wiki/Bituminous_waterproofing

    Felt paper is available in several grades, the most common being Type 1—commonly called 15-pound (15#) or No. 15 (#15)—and Type 2—commonly called 30-pound (30#) or No. 30 (#30). The weight designations originated with organic base felt weighing 15 or 30 pounds per 100 sq. ft. (6.8 kg or 14 kg per 9.3 m 2 ).

  3. Tar paper - Wikipedia

    en.wikipedia.org/wiki/Tar_paper

    Tar paper is used as a roofing underlayment with asphalt, wood, shake, and other roof shingles as a form of intermediate bituminous waterproofing.It is sold in rolls of various widths, lengths, and thicknesses – 3-foot-wide (0.91 m) rolls, 50 or 100 feet (15 or 30 m) long and "15 lb" (7 kg) and "30 lb" (14 kg) weights are common in the U.S. – often marked with chalk lines at certain ...

  4. BS 1088 - Wikipedia

    en.wikipedia.org/wiki/BS_1088

    Moisture Content-- BS 1088 plywood must have a moisture content between 6% and 14% when it leaves the factory. Finishing -- Boards will be sanded on both sides equally. Length & Width -- The length or width of a board produced as a standard size shall not be less than the specified size nor more than 6.3 mm (0.25") greater than the specified size.

  5. Wood veneer - Wikipedia

    en.wikipedia.org/wiki/Wood_veneer

    Once dyed, the sheets are laminated together to form a block. The block is then sliced so that the edges of the laminated veneer become the “grain” of the reconstituted veneer. Wood on Wood Also called 2-ply is a decorative wood veneer face with a utility grade wood backer applied at an opposing direction to the face veneer.

  6. Pressed wood - Wikipedia

    en.wikipedia.org/wiki/Pressed_wood

    The creation of pressed wood begins with the veneers [2] being placed in a rotary dryer. [3] This dryer is typically heated with steam at around 204 °C (400 °F). This process prepares the veneers for the humidifying process in which the veneers are then placed into humidification chambers.

  7. Wood preservation - Wikipedia

    en.wikipedia.org/wiki/Wood_preservation

    The American Wood Protection Association (AWPA) standards for ACQ require a retention of 0.15 lb/cu ft (2.4 kg/m 3) for above ground use and 0.40 lb/cu ft (6.4 kg/m 3) for ground contact. Chemical Specialties, Inc (CSI, now Viance) received U.S. Environmental Protection Agency 's Presidential Green Chemistry Challenge Award in 2002 for ...

  8. Specific modulus - Wikipedia

    en.wikipedia.org/wiki/Specific_modulus

    It is also known as the stiffness to weight ratio or specific stiffness. High specific modulus materials find wide application in aerospace applications where minimum structural weight is required. The dimensional analysis yields units of distance squared per time squared.

  9. Lumber - Wikipedia

    en.wikipedia.org/wiki/Lumber

    The wood moisture content is above 25% on a dry-weight basis; The environment is sufficiently warm; Oxygen (O 2) is present; Wood with less than 25% moisture (dry weight basis) can remain free of decay for centuries. Similarly, wood submerged in water may not be attacked by fungi if the amount of oxygen is inadequate. Fungi lumber/timber ...

  1. Ads

    related to: 30lb felt vs 15 lb oak plywood sheets dimensions weight