enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Template:Convert/list of units - Wikipedia

   en.wikipedia.org/wiki/Template:Convert/list_of_units

   {{convert|100|lb|kg}} → 100 pounds (45 kg) The unit-codes should be treated as case-sensitive: {{convert|100|Mm|mm}} → 100 megametres (1.0 × 10 11 mm) The output of {{convert}} can display multiple converted units, if further unit-codes are specified after the second unnamed parameter (without the pipe separator). Typical combination ...

3. Help:Convert - Wikipedia

   en.wikipedia.org/wiki/Help:Convert

   By default, the output value is rounded to adjust its precision to match that of the input. An input such as 1234 is interpreted as 1234 ± 0.5, while 1200 is interpreted as 1200 ± 50, and the output value is displayed accordingly, taking into account the scale factor used in the conversion.

4. Template:Convert - Wikipedia

   en.wikipedia.org/wiki/Template:Convert

   Converts measurements to other units. Template parameters [Edit template data] This template prefers inline formatting of parameters. Parameter Description Type Status Value 1 The value to convert. Number required From unit 2 The unit for the provided value. Suggested values km2 m2 cm2 mm2 ha sqmi acre sqyd sqft sqin km m cm mm mi yd ft in kg g mg lb oz m/s km/h mph K C F m3 cm3 mm3 L mL cuft ...

5. Template:Height - Wikipedia

   en.wikipedia.org/wiki/Template:Height

   The template is intended for conversion of heights specified in either metres or in feet and inches. Template parameters [Edit template data] Parameter Description Type Status Metres m metre metres meter meters The height in metres. Do not use if feet and inches are specified. Number optional Centimetres cm centimetre centimetres centimeter centimeters The height in centimetres. Do not use if ...

6. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Wrench_size

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

7. Conversion of units - Wikipedia

   en.wikipedia.org/wiki/Conversion_of_units

   For example, the freezing point of water is 0 °C and 32 °F, and a 5 °C change is the same as a 9 °F change. Thus, to convert from units of Fahrenheit to units of Celsius, one subtracts 32 °F (the offset from the point of reference), divides by 9 °F and multiplies by 5 °C (scales by the ratio of units), and adds 0 °C (the offset from the ...

8. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

9. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.