enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Edison screw - Wikipedia

   en.wikipedia.org/wiki/Edison_screw

   The medium Edison screw has seven threads per inch, or a pitch of 1 ⁄ 7 in or 3.6286 mm per thread. In the U.S., the Energy Independence and Security Act of 2007 requirement for greater energy efficiency only applies to the medium Edison screw, all other being considered "specialty" lamps.

3. AN thread - Wikipedia

   en.wikipedia.org/wiki/AN_thread

   AN sizes range from -2 (dash two) to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in 1 ⁄ 16-inch increments. Therefore, a -8 AN size would be equal to 1 ⁄ 2-inch OD tube. However, this system does not specify the ID (inside diameter) of the tubing because the tube wall can vary in thickness ...

4. Gooseneck lamp - Wikipedia

   en.wikipedia.org/wiki/Gooseneck_lamp

   A gooseneck lamp is a type of light fixture in which a lamp or lightbulb is attached to a flexible, adjustable shaft known as a "gooseneck" to allow the user to position the light source without moving the fixture or item to be illuminated. [1] Gooseneck lamps are often used to position a light for reading, or in industry, to provide spot ...

5. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   American Society of Mechanical Engineers National Pipe Thread Taper (NPT) [5] Nominal pipe size Thread density Thread pitch P Hand-tight engagement [6] Effective thread [6] Overall length L 4 [6] Actual outside diameter D Tap drill; Length L 1 Turns Diameter E 1 Length L 2 Turns Diameter E 2; inch inch −1 inch mm inch inch inch inch inch inch ...

6. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

7. A-series light bulb - Wikipedia

   en.wikipedia.org/wiki/A-series_light_bulb

   The most commonly used A-series light bulb type is an A60 bulb [7] (or its inch-based equivalent, the A19 bulb [2] [4]), which is 60 mm (19 ⁄ 8 in or 2 + 3 ⁄ 8 in) wide at its widest point [3] and approximately 110 mm (4 + 3 ⁄ 8 in) in length. [8] Other sizes with a data sheet in IEC 60064 are A50, A55, A67, A68, A71, A75, and A80.

8. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

9. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   the words, Pipe thread, the document number of the standard (e.g., ISO 7 or EN 10226) the symbol for the pipe thread type: G, external and internal parallel (ISO 228) R, external taper (ISO 7) Rp, internal parallel (ISO 7/1) Rc, internal taper (ISO 7) Rs, external parallel; the thread size; Threads are normally right-hand.