enow.com Web Search

  1. Ads

    related to: lumber length dimensions width height thickness measurements

Search results

  1. Results from the WOW.Com Content Network
  2. Board foot - Wikipedia

    en.wikipedia.org/wiki/Board_foot

    The board foot or board-foot is a unit of measurement for the volume of lumber in the United States and Canada.It equals the volume of a board that is one foot (30.5 cm) in length, one foot (30.5 cm) in width, and one inch (2.54 cm) in thickness, or exactly 2.359 737 216 liters.

  3. Lumber - Wikipedia

    en.wikipedia.org/wiki/Lumber

    As previously noted, less wood is needed to produce a given finished size than when standards called for the green lumber to be the full nominal dimension. However, even the dimensions for finished lumber of a given nominal size have changed over time. In 1910, a typical finished 1-inch (25 mm) board was 13 ⁄ 16 in (21 mm). In 1928, that was ...

  4. Plank (wood) - Wikipedia

    en.wikipedia.org/wiki/Plank_(wood)

    The wood is categorized as a board if its width is less than 2 + 1 ⁄ 2 in (64 mm), and its thickness is less than 1 + 1 ⁄ 2 in (38 mm). A plank used in a building as a horizontal supporting member that runs between foundations, walls, or beams to support a ceiling or floor is called a joist .

  5. Parallel-strand lumber - Wikipedia

    en.wikipedia.org/wiki/Parallel-strand_lumber

    The beams are continuously formed, so the length of the beam is limited only to the maximum length that can be handled and transported. Typical widths are 3 + 1 ⁄ 2, 5 + 1 ⁄ 4 or 7 inches (89, 133 or 178 mm); typical depths are 9 + 1 ⁄ 2, 11 + 7 ⁄ 8, 14, 16 and 18 inches (240, 300, 360, 410 and 460 mm). Typically the beams are made to a ...

  6. Wall stud - Wikipedia

    en.wikipedia.org/wiki/Wall_stud

    Typical dimensions of today's "two by four" is 1.5 by 3.5 inches (38 mm × 89 mm) dimensional lumber prior to sanding and are typically placed 16 inches (406 mm) from each other's center, but sometimes also at 12 inches (305 mm) or 24 inches (610 mm).

  7. Standard (timber unit) - Wikipedia

    en.wikipedia.org/wiki/Standard_(timber_unit)

    The countries of the Baltic region were major producers and exporters of timber, and used their local measure for trade with other countries such as Britain. The hundred in the term standard hundred was usually a long hundred , meaning 120 pieces, but the word hundred was often dropped, leaving simply standard to mean "the local standard number ...

  8. Shiplap - Wikipedia

    en.wikipedia.org/wiki/Shiplap

    Shiplap is either rough-sawn 25 mm (1 in) or milled 19 mm (3 ⁄ 4 in) pine or similarly inexpensive wood between 76 and 254 mm (3 and 10 in) wide with a 9.5–12.7 mm (3 ⁄ 8 – 1 ⁄ 2 in) rabbet on opposite sides of each edge. [1]

  9. Plywood - Wikipedia

    en.wikipedia.org/wiki/Plywood

    The most common dimension is 1.2 by 2.4 metres (3 ft 11 in × 7 ft 10 in) or the slightly larger imperial dimension of 4 feet × 8 feet. Plies vary in thickness from 1.4 mm to 4.3 mm. The number of plies—which is always odd—depends on the thickness and grade of the sheet. Roofing can use the thinner 16-millimetre (5 ⁄ 8 in) plywood.

  1. Ads

    related to: lumber length dimensions width height thickness measurements