enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   The taper rate for all NPT threads is 1 inch of diameter in 16 inches of length (3 ⁄ 4 inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance of thread. The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′.

3. Organ flue pipe scaling - Wikipedia

   en.wikipedia.org/wiki/Organ_flue_pipe_scaling

   Relationship between number of feet, octave and size of an open flue pipe (1′ = 1 foot = about 32 cm) Play ⓘ Scaling is the ratio of an organ pipe's diameter to its length. The scaling of a pipe is a major influence on its timbre. Reed pipes are scaled according to different formulas than for flue pipes.

4. Orders of magnitude (length) - Wikipedia

   en.wikipedia.org/wiki/Orders_of_magnitude_(length)

   10.16 cm = 1.016 dm – 1 hand used in measuring height of horses (4 inches) 12 cm = 1.2 dm – diameter of a compact disc (CD) (= 120 mm) 15 cm = 1.5 dm – length of a Bic pen with cap on; 22 cm = 2.2 dm – diameter of a typical association football (soccer ball) 30 cm = 3 dm – typical school-use ruler length (= 300 mm)

5. French catheter scale - Wikipedia

   en.wikipedia.org/wiki/French_catheter_scale

   The French scale measures the outer diameter of the catheter, not the size of the internal drainage channel (inner diameter). For instance, a two-way catheter of 20 Fr and a three-way catheter of 20 Fr have the same outer diameter, but the three-way catheter has an additional channel for irrigation, reducing the size of its drainage channel.

6. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

7. Center-pivot irrigation - Wikipedia

   en.wikipedia.org/wiki/Center-pivot_irrigation

   Trowbridge put up $25,000 (equivalent to $296,000 in 2024) and got 49% of the patent rights. Zybach moved back from Colorado to Columbus, opened a shop, hired a few men, moved the height of the pipe up to 1.8 m (6 ft), and went into business. In the first two years of operation, they sold only 19 systems.

8. Iron pipe size - Wikipedia

   en.wikipedia.org/wiki/Iron_pipe_size

   During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. [1] The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different ...

9. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   Consequently, a 1-inch (25 mm) copper pipe had a 1 + 1 ⁄ 8-inch (28.58 mm) outside diameter. The outside diameter was the important dimension for mating with fittings. The wall thickness on modern copper is usually thinner than 1 ⁄ 16-inch (1.6 mm), so the internal diameter is only "nominal" rather than a controlling dimension. [13]