enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Parts-per notation - Wikipedia

    en.wikipedia.org/wiki/Parts-per_notation

    Fluorescein aqueous solutions, diluted from 10,000 to 1 parts-per-million in intervals of 10 fold dilution. At 1 ppm the solution is a very pale yellow. As the concentration increases the colour becomes a more vibrant yellow, then orange, with the final 10,000 ppm a deep red colour.

  3. Air pollutant concentrations - Wikipedia

    en.wikipedia.org/wiki/Air_pollutant_concentrations

    1 volume percent = 10,000 ppmv (i.e., parts per million by volume) with a million being defined as 10 6. Care must be taken with the concentrations expressed as ppbv to differentiate between the British billion which is 10 12 and the USA billion which is 10 9 (also referred to as the long scale and short scale billion, respectively).

  4. Useful conversions and formulas for air dispersion modeling

    en.wikipedia.org/wiki/Useful_conversions_and...

    Although ppmv and grains per dscf have been used in the above examples, concentrations such as ppbv (i.e., parts per billion by volume), volume percent, grams per dscm and many others may also be used. 1 percent by volume = 10,000 ppmv (i.e., parts per million by volume).

  5. Total dissolved solids - Wikipedia

    en.wikipedia.org/wiki/Total_dissolved_solids

    where TDS is expressed in mg/L and EC is the electrical conductivity in microsiemens per centimeter at 25 °C. The conversion factor k e varies between 0.55 and 0.8. [5] Some TDS meters use an electrical conductivity measurement to the ppm using the above formula. Regarding units, 1 ppm indicates 1 mg of dissolved solids per 1,000 g of water. [6]

  6. Threshold limit value - Wikipedia

    en.wikipedia.org/wiki/Threshold_limit_value

    The TLV for chemical substances is defined as a concentration in air, typically for inhalation or skin exposure. Its units are in parts per million (ppm) for gases and in milligrams per cubic meter (mg/m 3) for particulates such as dust, smoke and mist.

  7. Talk:Parts-per notation - Wikipedia

    en.wikipedia.org/wiki/Talk:Parts-per_notation

    The examples don't seem to be too accurate. A drop is usually defined as 0.05 ml, which then gives;. 1 drop in 50 ml = 1‰, 50ml is a very small cup 1 drop in 50 l = 1ppm 50 l is about 11 gallons, not 40 1 drop in 50 cubic metres = 1 ppb 1 drop = 1ppt, a 50 m swimming pool is 50*25*2 = 2,500 m^3 1 drop in 50,000,000 cubic metres = 1ppq, 50,000,000 m^3 is equivalent to a lake covering a square ...

  8. Study: 21 popular cereals found to have cancer-linked ... - AOL

    www.aol.com/lifestyle/study-21-popular-cereals...

    The U.S. Environmental Protection Agency, however, has a much higher tolerance for glysphosate in crops, allowing levels ranging from 0.1 to 310 parts per million.

  9. Conversion of units - Wikipedia

    en.wikipedia.org/wiki/Conversion_of_units

    NO x concentration = 10 parts per million by volume = 10 ppmv = 10 volumes/10 6 volumes NO x molar mass = 46 kg/kmol = 46 g/mol Flow rate of flue gas = 20 cubic metres per minute = 20 m 3 /min The flue gas exits the furnace at 0 °C temperature and 101.325 kPa absolute pressure.