enow.com Web Search

Search results

  1. Results from the WOW.Com Content Network
  2. Number Forms - Wikipedia

    en.wikipedia.org/wiki/Number_Forms

    1 ⁄ 9: 0.111... Vulgar Fraction One Ninth 2151 8529 ⅒ 1 ⁄ 10: 0.1 Vulgar Fraction One Tenth 2152 8530 ⅓ 1 ⁄ 3: 0.333... Vulgar Fraction One Third 2153 8531 ⅔ 2 ⁄ 3: 0.666... Vulgar Fraction Two Thirds 2154 8532 ⅕ 1 ⁄ 5: 0.2 Vulgar Fraction One Fifth 2155 8533 ⅖ 25: 0.4 Vulgar Fraction Two Fifths 2156 8534 ⅗ 3 ⁄ 5: 0 ...

  3. Fraction - Wikipedia

    en.wikipedia.org/wiki/Fraction

    The entire fraction may be expressed as a single composition, in which case it is hyphenated, or as a number of fractions with a numerator of one, in which case they are not. (For example, "two-fifths" is the fraction2 / 5 ⁠ and "two fifths" is the same fraction understood as 2 instances of ⁠ 1 / 5 ⁠.) Fractions should always be ...

  4. 3/8 - Wikipedia

    en.wikipedia.org/wiki/3/8

    the fraction, three eighths or 0.375 in decimal; a time signature; 3/8, a 2007 album by Kay Tse This page was last edited on 19 April ...

  5. Single-precision floating-point format - Wikipedia

    en.wikipedia.org/wiki/Single-precision_floating...

    Thus only 23 fraction bits of the significand appear in the memory format, but the total precision is 24 bits (equivalent to log 10 (2 24) ≈ 7.225 decimal digits) for normal values; subnormals have gracefully degrading precision down to 1 bit for the smallest non-zero value. The bits are laid out as follows:

  6. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    The major minus pitch technique also works for inch-based threads, but you must first calculate the pitch by converting the fraction of threads-per-inch (TPI) into a decimal. For example, a screw with a pitch of 1/20 in (20 threads per inch) has a pitch of 0.050 in and a 1 ⁄ 13 in pitch (13 threads per inch) has a pitch of 0.077 in.

  7. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    Below is a chart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for .25, .5, and .75 are shown to thousandths [.250, .500, .750], which is how machinists usually think about them ["two-fifty", "five hundred", "seven-fifty"]. Machinists generally ...

  8. Binary number - Wikipedia

    en.wikipedia.org/wiki/Binary_number

    In the example below, the divisor is 101 2, or 5 in decimal, while the dividend is 11011 2, or 27 in decimal. The procedure is the same as that of decimal long division; here, the divisor 101 2 goes into the first three digits 110 2 of the dividend one time, so a "1" is written on the top line. This result is multiplied by the divisor, and ...

  9. Decimal separator - Wikipedia

    en.wikipedia.org/wiki/Decimal_separator

    [6] [2] [7] In some specialized contexts, the word decimal is instead used for this purpose (such as in International Civil Aviation Organization-regulated air traffic control communications). In mathematics, the decimal separator is a type of radix point, a term that also applies to number systems with bases other than ten.