enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. AN thread - Wikipedia

   en.wikipedia.org/wiki/AN_thread

   AN sizes range from -2 (dash two) to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in 1 ⁄ 16-inch increments. Therefore, a -8 AN size would be equal to 1 ⁄ 2-inch OD tube. However, this system does not specify the ID (inside diameter) of the tubing because the tube wall can vary in thickness ...

3. National pipe thread - Wikipedia

   en.wikipedia.org/wiki/National_pipe_thread

   American Society of Mechanical Engineers National Pipe Thread Taper (NPT) [5] Nominal pipe size Thread density Thread pitch P Hand-tight engagement [6] Effective thread [6] Overall length L 4 [6] Actual outside diameter D Tap drill; Length L 1 Turns Diameter E 1 Length L 2 Turns Diameter E 2; inch inch −1 inch mm inch inch inch inch inch inch ...

4. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe Thread Form ASME B1.21M-1997 (R2013) Metric Screw Threads - MJ Profile: V Thread Form BS 84: Tables of BS Whitworth, BS Fine and BS Pipe Threads: V Thread Form (55°) 1 ⁄ 4 ″-20 BSW ISO 68-1:1998: ISO general purpose screw threads ...

5. Tube (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Tube_(fluid_conveyance)

   Both pipe and tube imply a level of rigidity and permanence, whereas a hose is usually portable and flexible. A tube and pipe may be specified by standard pipe size designations, e.g., nominal pipe size, or by nominal outside or inside diameter and/or wall thickness. The actual dimensions of pipe are usually not the nominal dimensions: A 1-inch ...

6. Pipe (fluid conveyance) - Wikipedia

   en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

   Consequently, a 1-inch (25 mm) copper pipe had a 1 + 1 ⁄ 8-inch (28.58 mm) outside diameter. The outside diameter was the important dimension for mating with fittings. The wall thickness on modern copper is usually thinner than 1 ⁄ 16-inch (1.6 mm), so the internal diameter is only "nominal" rather than a controlling dimension. [13]

7. British Standard Pipe - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Pipe

   the words, Pipe thread, the document number of the standard (e.g., ISO 7 or EN 10226) the symbol for the pipe thread type: G, external and internal parallel (ISO 228) R, external taper (ISO 7) Rp, internal parallel (ISO 7/1) Rc, internal taper (ISO 7) Rs, external parallel; the thread size; Threads are normally right-hand.

8. Nominal Pipe Size - Wikipedia

   en.wikipedia.org/wiki/Nominal_Pipe_Size

   Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

9. Garden hose - Wikipedia

   en.wikipedia.org/wiki/Garden_hose

   This fitting is used with 1 ⁄ 2-inch, 5 ⁄ 8-inch, and 3 ⁄ 4-inch hoses. [4] [5] In other countries, a British Standard Pipe (BSP) thread is used, which is 3 ⁄ 4 inch (19 mm) and 14 TPI (male part outside diameter is 26.441 mm or 1.04 in). The GHT and BSP standards are not compatible, and attempting to connect a GHT hose to a BSP fitting ...