Search results
Results from the WOW.Com Content Network
The Charrière is measured by the ''outer'' diameter, and is defined as 1 Fr = 1/3 mm, and thus 1 mm = 3 Fr; therefore the diameter of a round catheter in millimetres can be determined by dividing the French size by 3. [2] The French units roughly correspond to the outer circumference of the catheter (see table below).
Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...
Fontanini produces 5 inch nativity scene figures at this scale. 1:14: 0.8571428 in: 21.77 mm Tamiya Tamiya 56301 RC 1:14 King Hauler, RC Tractor Trucks 1:14 Scale. 1:13.71: 22.225 mm Model railway scratchbuilders' scale at 7 ⁄ 8 inches to a foot, commonly used with 45 mm gauge track to represent 2 ft gauge prototypes. 1:13: 59 ⁄ 64 in: 23.44 mm
Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.
Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.
32 gauge — .526 in (13.4 mm) 28 gauge — .550 in (14.0 mm) 24 gauge — .579 in (14.7 mm) 20 gauge — .615 in (15.6 mm) 16 gauge — .663 in (16.8 mm) 14 gauge — .693 in (17.6 mm) 12 gauge — .729 in (18.5 mm) 10 bore — .775 in (19.7 mm) 8 bore — .835 in (21.2 mm) 6 bore — .919 in (23.3 mm) 4 bore — 1.052 in (26.7 mm)
14 mm 0.8 g 0.750 fine 1851–1853 14 mm 0.75 g 0.900 fine 1854–1873 Half Dime 15.5 mm 1.24 g 1794–1873 Dollar 15 mm 1.67 gr 1849–1889 $5 American Gold Eagle 16.5 mm 3.11 g 1986–present $10 American Platinum Eagle 16.5 mm 3.11 g 1997–present Three Cent 17.9 mm 1.94 g 1865-1889 Dime (Clad) 17.91 mm 2.268 g 1965–present Dime 17.9 mm 2 ...
Originally in 1945, the divisions were based on the ring inside diameter in steps of 1 ⁄ 64 inch (0.40 mm). [6] However, in 1987 BSI updated the standard to the metric system so that one alphabetical size division equals 1.25 mm of circumferential length. For a baseline, ring size C has a circumference of 40 mm. [7]