enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. Gear inches - Wikipedia

   en.wikipedia.org/wiki/Gear_inches

   For bicycles with 700c wheels, some cyclists quote gear inches based on a nominal wheel diameter of 27 inches, corresponding to the old British tire size of 27 x 1 + 1 ⁄ 4" (ETRTO 630). Strictly speaking, the rolling diameter of a 700c wheel may be significantly higher or lower than 27", depending on the tire size, e.g. nearly 27.5" for a ...

3. List of GM transmissions - Wikipedia

   en.wikipedia.org/wiki/List_of_GM_transmissions

   New Process Gear A833 RPO MY6 or MM7 — 4-speed longitudinal A833 overdrive transmission made by New Process Gear for early to mid 1980s General Motors Light Trucks; Muncie SM465 — 4-speed longitudinal manual used in 68- 91 Chevy 1/2 3/4 and 1 ton trucks; New Venture Gear NV1500 — 5-speed longitudinal manual made by New Venture Gear

4. Dana 70 - Wikipedia

   en.wikipedia.org/wiki/Dana_70

   The Dana 70 axle only came with 5.13:1, 4.88,5.31 [citation needed] gear ratios and had a GAWR of [citation needed] these axles were rated at 7-9klbs as seen on 5500 door stickers. They differ greatly from previous Dana 70 front axles, some of the major differences being the use of 1550 Universal Joints and being a high pinion, reverse cut axle.

5. Wheel sizing - Wikipedia

   en.wikipedia.org/wiki/Wheel_sizing

   Modern road tires have several measurements associated with their size as specified by tire codes like 225/70R14. The first number in the code (e.g., "225") represents the nominal tire width in millimeters. This is followed by the aspect ratio (e.g.,"70"), which is the height of the sidewall expressed as a percentage of the nominal tire width.

6. GM 4T40 transmission - Wikipedia

   en.wikipedia.org/wiki/GM_4T40_transmission

   The "MN4" 4T40E is able to handle vehicles up to 4000 lb (1814 kg) GVWR. The final drive ratio can vary depending on the car's curb weight and3wweteeengine power output. 3.91, 3.63, 3.29, 3.05, 3.69, and 3.42 are all of the available ratios used in the 4T40 (and 4T45) transmission; Made possible by using combinations selected from 3 different sprocket combinations (32/38, 35/35, 33/37) and 2 ...

7. Getrag 282 transmission - Wikipedia

   en.wikipedia.org/wiki/Getrag_282_transmission

   All transmissions have a third gear ratio of 1.38:1. However, third and fourth gear are clustered on the counter shaft which was available with two different fourth gear ratios: 1.03:1 or .94:1. Fifth gear is independently interchangeable and available with a .80:1 and .72:1 ratio.

8. GM 8L transmission - Wikipedia

   en.wikipedia.org/wiki/GM_8L_transmission

   The main objective in replacing the predecessor model was to improve vehicle fuel economy with extra speeds and a wider gear span to allow the engine speed level to be lowered (downspeeding). The layout brings the ability to shift in a non-sequential manner – going from gear 8 to gear 2 in extreme situations simply by changing one shift ...

9. GM 10.5-inch 14-bolt differential - Wikipedia

   en.wikipedia.org/wiki/GM_10.5-inch_14-bolt...

   The 11.5 AAM 14-bolt rear differential started replacing the 10.5" 14-bolt in Chevrolet Silverado and GMC Sierra trucks from the 2001 model year onwards. However, the 10.5" 14-bolt axle remains in production today, specifically utilized in GMC Savana and Chevrolet Express vans.