enow.com Web Search

Search results

1. Results from the WOW.Com Content Network

2. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

3. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25).

4. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993: ISO general-purpose metric screw threads—Basic dimensions: V Thread Form ISO 725:2009: ISO inch screw threads—Basic dimensions: V Thread ...

5. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   Nominal (thread) sizes range from 0.1875 to 0.375 in (4.763 to 9.525 mm) and lengths from 1.25 to 5 in (32 to 127 mm). Typically an installer uses a hammer drill to make a pilot hole for each concrete screw and a powered impact driver to drive the screw. The drill hole should be 1/2" longer than the depth penetration of the screw.

6. Preferred metric sizes - Wikipedia

   en.wikipedia.org/wiki/Preferred_metric_sizes

   Machine screws with different thread diameters Hex key set with metric sizes from 2 mm to 10 mm according to sizes for use with ISO 262 screw sizes (except 3.5 mm for M6 internal set screw) For each size bolt or screw and type of head, there is a corresponding size driver prescribed by various ISO standards, including: Internal hex drive: ISO ...

7. List of screw drives - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_drives

   In Japan, the male sizes are often designated as DTC-20, DTC-27, DTC-40 (discontinued) and DTC-45 corresponding to a respective screw head size of 3.2 mm, 4.6 mm, 6.4 mm and 7.7 mm; with the size of the screw measured across the widest portion of the mating part of the head. The most common sizes in use for consumer electronics are DTC-20 and ...

8. Computer case screws - Wikipedia

   en.wikipedia.org/wiki/Computer_case_screws

   A regular computer case may require/include [5] 7 thumb screw 6-32 × 6 mm for 2.5” drive tray, expansion slots; 4 hexagon screw 6-32 × 6 mm for psu; 21 phillips screw 6-32 × 5 mm for motherboard, 3.5” harddisk tray; 12 phillips screw M3 × 5 mm for 2.5” harddrive; 16 KB5 x 10 mm for fans; 9 standoff 6-32 × 6.5 + 4 mm for motherboard

9. ISO 965 - Wikipedia

   en.wikipedia.org/wiki/ISO_965

   ISO 965 (ISO general purpose metric screw thread—tolerances) is an International Organization for Standardization (ISO) standard for metric screw thread tolerances. [1] It specifies the basic profile for ISO general purpose metric screw threads (M) conforming to ISO 261 .