enow.com Web Search

  1. Ads

    related to: measuring bolt length chart metric

Search results

  1. Results from the WOW.Com Content Network
  2. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    The length of a machine screw or bolt is indicated by an × and the length expressed in millimetres (e.g. M8-1.25×30 or M8×30). [citation needed] Tolerance classes defined in ISO 965-1 can be appended to these designations, if required (e.g. M500– 6g in external threads). External threads are designated by lowercase letter, g or h.

  3. Preferred metric sizes - Wikipedia

    en.wikipedia.org/wiki/Preferred_metric_sizes

    A standard metric (concrete) block is 190 mm wide, 390 mm long, and 190 mm high, which allows for 10 mm mortar joints in between bricks, giving a standard unit size of 200 mm square by 400 mm long. [3] A standard metric brick is 90 by 57 by 190 mm; with 10 mm of mortar, that produces a standard unit of 100 mm x 200 mm. [3]

  4. British Standard Whitworth - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Whitworth

    To simplify matters, the term hexagon is used in this section to denote either bolt head or nut. Two spanners, both nominal size 5 ⁄ 8 in, with a diagram superimposed to show the logic that allows them both to be nominal size 5 ⁄ 8 in when their actual sizes are clearly different (across-flats distance vs screw diameter). The across-flats ...

  5. Screw thread - Wikipedia

    en.wikipedia.org/wiki/Screw_thread

    Calipers measure the female minor diameter (inside diameter, ID), which is less than caliper measurement of the male major diameter (outside diameter, OD). For example, tables of caliper measurements show 0.69 female ID and 0.75 male OD for the standards of "3/4 SAE J512" threads and "3/4-14 UNF JIS SAE-J514 ISO 8434-2". [ 6 ]

  6. British Association screw threads - Wikipedia

    en.wikipedia.org/wiki/British_Association_screw...

    The major diameter is given by 6p 1.2, [4]: 12 rounded to two significant figures in mm and the hex head size (across the flats) is 1.75 times the major diameter. BA sizes are specified by the following British Standards: BS 57:1951 — B.A. screws, bolts and nuts

  7. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    spanner (wrench) size and thread diameter of a hex nut. Width across flats is the distance between two parallel surfaces on the head of a screw or bolt, or a nut, mostly for torque transmission by positive locking. The term width across flats (AF) is used for the following forms: 2-socket = round material with two surfaces

  8. United States Standard thread - Wikipedia

    en.wikipedia.org/wiki/United_States_Standard_thread

    The thread form is defined by flats at the tip and root of the thread form. This flat length is defined as the pitch divided by eight. The thread depth, which is from flat to flat is 0.6495 times the pitch. [4] For 1 ⁄ 4-inch (6.4 mm) screws and larger, the pitch is defined as: = +

  9. British Standard Fine - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Fine

    British Standard Fine (BSF) is a screw thread form, as a fine-pitch alternative to British Standard Whitworth (BSW) thread. It was used for steel bolts and nuts on and in much of Britain's machinery, including cars, prior to adoption of Unified, and later Metric, standards.

  1. Ads

    related to: measuring bolt length chart metric