Search results
Results from the WOW.Com Content Network
In digital photography, the image sensor format is the shape and size of the image sensor. The image sensor format of a digital camera determines the angle of view of a particular lens when used with a particular sensor. Because the image sensors in many digital cameras are smaller than the 24 mm × 36 mm image area of full-frame 35 mm cameras ...
5 1 ⁄ 4 inch Double 1 40 8 512 soft 160 kB 300 MFM Commodore 64 (8-bit) 5 1 ⁄ 4 inch Double 1 35 Variable (17-21) ZCAV: 256 soft 170 kB 300 GCR [NB 6] 2 340 kB Quad 1 77 Variable (23-29) ZCAV 521 kB 2 1,042 kB 3 1 ⁄ 2 inch Double 2 80 10 512 800 kB MFM Commodore Amiga: 5 1 ⁄ 4 inch Double 2 40 11 512 soft 440 kB [NB 7] 300 MFM [NB 8 ...
8-, 5.25-, 3.5-, 2.5-, 1.8- and 1-inch HDDs, together with a ruler to show the length of platters and read-write heads A newer 2.5-inch (63.5 mm) 6,495 MB HDD compared to an older 5.25-inch full-height 110 MB HDD. IBM's first hard drive, the IBM 350, used a stack of fifty 24-inch platters and was of a size comparable to two large refrigerators.
8-inch floppy disk, inserted in drive, (3½-inch floppy diskette, in front, shown for scale) 3½-inch, high-density floppy diskettes with adhesive labels affixed The first commercial floppy disks, developed in the late 1960s, were 8 inches (203.2 mm) in diameter; [4] [5] they became commercially available in 1971 as a component of IBM products and both drives and disks were then sold ...
In the normal series, the long edge is the length of the short edge plus 2 inches (10 in or less) or 3 inches (11 in and above). The alternative Super series, denoted SnR, nR Plus or nR+, has an aspect ratio of 3∶2 (or as close as possible) and thus provides a better fit for standard 135 film (35 mm) at sizes of 8 inches or above. 5R is twice ...
By 1988, the 3 + 1 ⁄ 2-inch was outselling the 5 + 1 ⁄ 4-inch. [69] In South Africa, the 3 + 1 ⁄ 2-inch format was generally called a stiffy disk, to distinguish it from the flexible 5 + 1 ⁄ 4-inch format. [70] [71] The term "3 + 1 ⁄ 2-inch" or "3.5-inch" disk is and was rounded from the 90 mm actual dimension of one side of the ...
Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.
Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.